Effects of In/Ce to Sn-3.5Ag Lead-Free Solder on Microstructures and Properties

Abstract:

The Sn-3.5Ag based lead-free electronic solder doped with element In /Ce were prepared respectively using a smelting method with protection by molten salt (SMPMS). The effects of In addition and Ce addition on microstructure, melting point and wettability of Sn-3.5Ag solder were investigated comparatively. And the effects of addition on the intermetallic compound (IMC) layer formed at solder/Cu substrate interface and the shear strength of solder joint were also studied. The results showed that appropriate In or Ce addition can refine Ag₃Sn grains and improve the shear strength of solder joint. Element In can significantly reduce the melting point, narrow the melting range of the solder alloy and improve wettability on Cu substrate. When the content of In was 3%, the spreading area was the largest and the wettability was the best. The addition of Ce can efficiently reduce the thickness of the IMC layer grown at the solder/Cu substrate interface and improve the shear strength of solder joint. When the content of Ce was 0.5%, the solder joint had the minimum average IMC thickness and the maximum shear strength.

• Periodical: Materials Science Forum (Volume 749)
• Pages: 198-204
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.749.198
• Online since: March 2013
• Authors: En Jia Chen, Xiu Chen Zhao, Ying Liu, Dong Mei Li, Jing Wei Cheng, Hong Li
• Keywords: Lead-Free Solder, Rare Earth Element, Sn-Ag Based Solder

References

[1] W. Gibson, S. Choi, T.R. Bieler, K.N. Subramanian, Environmental concers and materials issues in manufactured solder joints. Proceedings of the 1997 IEEE International Symposium on Electronics and the Environment, San Francisco, CA, USA, May. 5-7 (1997).

DOI: 10.1109/isee.1997.605328

[2] M. Abtew, G. Selvaduray, Lead-Free Solders in Microelectronics, R. Mater. Sci. Eng. 27 (2000) 95-141.

DOI: 10.1016/s0927-796x(00)00010-3

[3] R. Mayappan, Wetting and intermetallic study between Sn-3. 5Ag-1. 0Cu-xZn lead-free solders and copper substrate (x=0, 0. 1, 0. 4, 0. 7), Adv. Mater. Res. 501 (2012) 150-154.

DOI: 10.4028/www.scientific.net/amr.501.150

[4] R.M. Shalaby, Effect of rapid solidification on mechanical properties of a lead free Sn-3. 5Ag solder, J. Alloys Compd. 27 (2010) 113-117.

DOI: 10.1016/j.jallcom.2010.05.179

[5] E.P. Wood, K.L. Nimmo, In search of new lead-free electronic solders, J. Electron. Mater. 23 (1994) 709-713.

DOI: 10.1007/bf02651363

[6] D.Q. Yu, J. Zhao, L. Wang, Improvement on the microstructure stability, mechanical and wetting properties of Sn-Ag-Cu lead-free solder with the addition of rare earth elements, J. Alloys Compd. 37 (2004) 6170-6175.

DOI: 10.1016/j.jallcom.2004.01.012

[7] C.M.L. Wu, D.Q. Yu, C.M.T. Law, L. Wang, Microstructure and mechanical properties of new lead-free Sn -Cu-RE solder alloys, J. Electron. Mater. 31 (2002) 928-932.

DOI: 10.1007/s11664-002-0185-5

[8] J.L. Shen, Y.C. Liu, H.X. Gao, The effects of third alloying elements on the bulk Ag3Sn formation in slowly cooled Sn-3. 5Ag lead-free solder, J. Mater. Sci. - Mater. Electron. 19 (3) (2008) 275-280.

DOI: 10.1007/s10854-007-9292-7

[9] H.T. Lee, Y.F. Chen, Influence of lanthanum additions on the microstructure and microhardness of sn-3. 5Ag solder, J. Electron. Mater. 38 (2009) 2148-2157.

DOI: 10.1007/s11664-009-0863-7

[10] S.E. Negm, H. Mady, A.A. Bahgat, Influence of the addition of indium on the mechanical creep of Sn-3. 5%Ag alloy, J. Alloys Compd. 30 (2010) 65-70.

DOI: 10.1016/j.jallcom.2010.05.007

[11] L. Wang, D.Q. Yu, J. Zhao, M.L. Huang, Improvement of wettability and tensile property in Sn-Ag-RE lead-free solder alloy, Mater. Lett. 56 (2002) 1039-1042.

DOI: 10.1016/s0167-577x(02)00672-9

[12] X. Ma, et al., Development of Cu-Sn intermetallic compound at Pb-free solder/Cu joint interface, Mater. Lett. 57 (2003) 3361-3365.

DOI: 10.1016/s0167-577x(03)00075-2

[13] J.W. Yoon, B.I. Noh, J.H. Choi, S.B. Jung, Effect of adding Ce on interfacial reactions between Sn-Ag solder and Cu, J. Mater. Sci. - Mater. Electron. 22 (2011) 745-750.

DOI: 10.1007/s10854-010-0204-x