Toughness of Ultra High Strength Steel Sheets

Stanislava Hlebová; Ladislav Pešek

doi:10.4028/www.scientific.net/MSF.782.57

Paper Titles

Modern Self-Lubricating Coatings for Automotive, Aviation and Spacecraft Industry
p.31

Evaluation of Grain Deformation in Polycrystals
p.41

Prediction of Ternary Fe-B-Cr Phase Diagram
p.45

Non-Traditional Use of Torsion Plastometer in Physical Simulation of Steel Production
p.51

Toughness of Ultra High Strength Steel Sheets
p.57

Effect of Experimental Factors on Hardness Measurement Using the UCI Technique
p.61

Experimental Analysis on the Causes of the Breakout of Continuous Cast Steel Slab
p.67

Precipitation in Surface Zone of Continuously-Cast Slab of ULC/IF Steel Microalloyed with Titanium
p.73

Influence of Casting Rate on TiNb Microalloyed Steel Slab Surface Area Microstructure
p.81

HomeMaterials Science ForumMaterials Science Forum Vol. 782Toughness of Ultra High Strength Steel Sheets

Toughness of Ultra High Strength Steel Sheets

Abstract:

Currently only few methods exist for thin steel sheet testing, especially based on fracture mechanics concept. Charpy impact test is one of the most used method for testing notch toughness and fracture behaviors because of the simplicity and the other advantages [. This article deals with toughness testing of automotive ultra high strength steel sheets (UHSS). Several standard types of toughness test that generate data for specific loading conditions and/or component design approaches exist. Two definition of toughness will be discussed: i) Charpy V-notch toughness, method includes joining of thin steel sheets to one compact unit and ii) material (tensile) toughness [. Two steels were used, DP1000 and 1400M of 1,8 mm thickness and two joining techniques: bonding with adhesives and joining with holders. Effect of material, joining technology, structural adhesives, and number of joined plates on the toughness values was quantified at the room temperature. Toughness of steels by the tensile test was added for comparison. Fracture surface was observed using scanning electron microscope analysis.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Materials Science Forum (Volume 782)

Pages:

57-60

DOI:

https://doi.org/10.4028/www.scientific.net/MSF.782.57

Citation:

Cite this paper

Online since:

April 2014

Authors:

Stanislava Hlebová*, Ladislav Pešek

Keywords:

Fracture Energy, Joining Technique, Structural Adhesive, Toughness, Ultra High Strength Steel

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] ASTM Standard E 1820-99.: Standard Test Method for Measurement of Fracture Toughness. In: Annual Book of ASTM Standards, (1999) 972-1005.

Google Scholar

[2] Information on http: /www. ndt-ed. org/ EducationResources/CommunityCollege/Materials/ Mechanical/Toughness. htm.

Google Scholar

[3] Technical Datasheet from Skoda Auto cz.

Google Scholar

[4] Information on http: /www. ksp. tul. cz/cz/kpt/obsah/vyuka/stud_materialy/mtk/MTK3. pdf.

Google Scholar

[5] Information on http: /commons. wikimedia. org/wiki/File: Brittle_v_ductile_stress-strain_behaviour. png.

Google Scholar

[6] H. Ono, R. Kasada, A. Kimura.: Specimen Size Effects on FractureToughness of JL–1 Reduced-activation Ferritic Steel. In: Journal of Nuclear Materials 329-333, (2004) 1117-1121.

DOI: 10.1016/j.jnucmat.2004.04.034

Google Scholar

[7] L. E Schubert.; et al.: Effect of Specimen Size on the Impact Properties of Neutron Irradiated A533B steel. In: Journal of Nuclear Materials 225, (1995) 231-237.

DOI: 10.1016/0022-3115(95)00052-6

Google Scholar

[8] E. Spišák, Ľ. Kačšák, J. Mucha.: Joining materials used in car body production by clinching. In: Chem. listy, 106 no. S, (2012) 541 - 544. ISSN 0009-2770.

Google Scholar