Low Temperature Boronizing of Surface Nanostructured Ni-Cr-Mo Steel Using SMAT

Abstract:

Boronizing is a surface thermochemical treatment in which boron atoms are made to diffuse into a metallic surface at high temperatures. A nano-crystalline surface with larger defect density assists in enhancing the diffusion rate even at low temperatures. In the present work Ni-Cr-Mo steel is subjected to a surface mechanical attrition treatment (SMAT) to activate the surface with nanocrystalline structures and crystal defects. Subsequently the samples were boronized at low temperature regime (400°C - 600°C) for 5 hours using a pack boronizing technique. The microstructure, chemical analysis and hardness of borided layers were investigated using optical microscope, SEM – EDX and Microvicker’s Hardness Tester. The SMAT treated samples showed severe plastic deformation of the surface, nano-structured grains (10-30 nm) and larger defect density illustrating mechanically activated surface for diffusion. The boronizing had clearly demonstrated the diffusion of boron even at 400°C. The thickness of diffused layer was found to be about 20 µm at 400°C and 50 µm at 600°C for SMAT samples while the untreated samples showed practically no diffusion at 400°C and 12 µm at 600°C. The SEM-EDX results had confirmed the presence of boron at the diffused layer; however the hardness was found to be low. A maximum of 650 HV_0.3 was achieved by low temperature boronizing of SMAT treated samples.

• Periodical: Materials Science Forum (Volumes 830-831)
• Pages: 663-666
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.830-831.663
• Online since: September 2015
• Authors: G. Sreejith*, Teotia Sunny, J.N. Sahu, Chandrabalan Sasikumar
• Keywords: Boronizing, Low Temperature Diffusion, SMAT, Surface Nanocrystallization

References

[1] N.R. Tao, Z.B. Wang, W.P. Tong, M.L. Sui, J. Lu, K. Lu, An investigation of surface nanocrystallization mechanism in Fe induced by surface mechanical attrition treatment, Acta Materialia 50 (2002) 4603–4616.

DOI: 10.1016/s1359-6454(02)00310-5

[2] Yimin Lin, Jian Lu, Liping Wang, Tao Xu, Qunji Xue, Surface nanocrystallization by surface mechanical attrition treatment and its effect on structure and properties of plasma nitrided AISI 321 stainless steel, Acta Materialia 54 (2006) 5599–5605.

DOI: 10.1016/j.actamat.2006.08.014

[3] K. Dai, L. Shaw, Comparison between shot peening and surface nanocrystallization and hardening processes, Materials Science and Engineering A 463 (2007) 46–53.

DOI: 10.1016/j.msea.2006.07.159

[4] A´. Re´ve´sz, L. Takacs, Coating metals by surface mechanical attrition treatment, Journal of Alloys and Compounds 441 (2007) 111–114.

DOI: 10.1016/j.jallcom.2006.09.081

[5] N.R. Tao, Z.B. Wang, W.P. Tong, M.L. Sui, J. Lu, K. Lu, An investigation of surface nanocrystallization mechanism in Fe induced by surface mechanical attrition treatment, Acta Mater. 50 (2002) 4603-4616.

DOI: 10.1016/s1359-6454(02)00310-5

[6] W.P. Tong, N.R. Tao, Z.B. Wang, H.W. Zhang, J. Lu, K. Lu, The formation of ε-Fe3–2N phase in a nanocrystalline Fe, Scripta Materialia 50 (2004) 647–650.

DOI: 10.1016/j.scriptamat.2003.11.022

[7] Kolobov YR, Grabovetskaya GP, Ivanov MB, Zhilyaev AP, Valiev, Grain boundary diffusion characteristics of nanostructured nickel, Scripta Mater. 2001; 44: 873.

DOI: 10.1016/s1359-6462(00)00699-0

[8] Z.B. Wang, N.R. Tao, W.P. Tong, J. Lu, K. Lu, Diffusion of chromium in nanocrystalline iron produced by means of surface mechanical attrition treatment, Acta Materialia 51 (2003) 4319–4329.

DOI: 10.1016/s1359-6454(03)00260-x

[9] W.P. Tong, Z. Han, L.M. Wang, J. Lu, K. Lu, Low-temperature nitriding of 38CrMoAl steel with a nanostructured surface layer induced by surface mechanical attrition treatment, Surface & Coatings Technology, vol. 202, 2008, p.4957–4963.

DOI: 10.1016/j.surfcoat.2008.04.085

[10] K. Genel, Boriding kinetics of H13 steel, Vacuum 80 (2006) 451–457.

DOI: 10.1016/j.vacuum.2005.07.013