Elucidation on the Microstructural and Mechanical Properties of Tailored VAL12 Hybrid Composites with ZrO₂ Dispersoids Fabricated by Squeeze Casting Technique

Abstract:

The effect of ZrO₂ (2, 4, 6 and 8 wt%) dispersoids with 1 wt% graphite on the microstructural, mechanical properties on squeeze cast VAL12 matrix hybrid composite is investigated in the present study. The hybrid composites were characterized using advanced characterization techniques to reveal its microstructural and physical properties. The microscopic examinations using optical and SEM technique reveal that the addition of dispersoids accelerates the nucleation kinetics, thus attaining fine, equiaxial grains in hybrid composites. The squeeze cast composites show almost nil porosity, defects and owing to it, the actual density of the composites are found to be more than 95% as that of the theoretical density values. The hardness values and tensile values increase with respect to the increase in percentage addition of ZrO₂. The tensile results show that there is an appreciable increase in the UTS values of composites without much loss in its ductility as the addition of graphite improves the self-lubricating property and provides wettability during the casting. Fractographic studies on tensile tested specimen reveal that the crack occurs in both matrix and particles showing the good interface between matrix and dispersoids. Machinability studies reveal the formation of continuous chips in hybrid composites with a lower percentage of reinforcement (up to 4% ZrO₂ + 1%Gr) and segmented chips in case of the composite with 8% ZrO₂ + 1%Gr, as the increase in the percentage of dispersoids improve the chip breakability of the composites. On an overall, the hybrid aluminium matrix composites with 1%Gr and 6 % ZrO₂ unveiled better optimal results.

• Periodical: Materials Science Forum (Volume 969)
• Pages: 813-818
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.969.813
• Online since: August 2019
• Authors: S.A. Srinivasan*, S.P. Kumaresh Babu, Vivek Gaurav
• Keywords: Hybrid Composites, Mechanical Properties, Squeeze Casting, VAL12

References

[1] H. Yamagata, The science and technology of materials in automotive engines, Woodhead, Cambridge, (2005).

[2] T. Ram Prabhu, An overview of high-performance aircraft structural Al alloy-AA7085, Acta Metall. Sin. (Engl. Lett.) 28 (2015) 909-921.

DOI: 10.1007/s40195-015-0275-z

[3] J. G. Kaufman, E. L. Rooy, Aluminum Alloy Castings- Properties, Processes, and Applications, ASM, OH, (2004).

[4] H. Kala, KKS Mer, Sandeep kumar, A Review on mechanical and tribological behaviors of stir cast aluminium matrix composites, Procedia Mater. Sci 6 (2014) 1951-1960.

DOI: 10.1016/j.mspro.2014.07.229

[5] C.H. Fan, Z.H. Chen, J.H. Chen, D.Chen, Effects of applied pressure on density, microstructure and tensile strength of Al–Zn– Mg–Cu alloy prepared by squeeze casting, Int. J. Cast Metal Res. 23-6 (2010) 349-353.

DOI: 10.1179/136404610x12693537270253

[6] V I Ryazantsev, V A Fedoseev, V N Matsnev, Construction of the welded body of vehicles from aluminium alloys, Welding Int. 14-5 (2000) 407-412.

DOI: 10.1080/09507110009549203

[7] N. A. Belov, Effect of eutectic phases on the fracture behavior of high-strength castable aluminum alloys, Met. Sci.heat Treat 37-5 (1995) 237-242.

DOI: 10.1007/bf01152226

[8] S. Madhusudana, M.M.M. Sarcarb, N.B. Rama Mohan Rao, Mechanical properties of Aluminum-Copper(p) composite metallic material, JART 14 (2016) 293-299.

[9] G. Zhang, J. Zhang, B. Li, W. Cai, Characterization of tensile fracture in heavily alloyed Al−Si piston alloy, Prog. Nat. Sci. 21 (2011) 380-385.

DOI: 10.1016/s1002-0071(12)60073-2

[10] P. Senthil, T.Selvaraj, K.Sivaprasad, Influence of turning parameters on the machinability of homogenized Al–Cu/TiB2 in situ metal matrix composites, Int. J. Adv. Manuf. Technol. 67 (2013) 1589-1596.

DOI: 10.1007/s00170-012-4592-3