Strength and Deformation of Bendable Plastic-Concrete-Tubal Structures

Abstract:

In modern construction production, structures with the use of tube concrete elements are increasingly used [1]. The use of such structures can significantly reduce the weight of the building, as well as reduce the cost of construction and installation works by 2-3 times compared with similar structures made of classical reinforced concrete. At the same time, labor costs are reduced by 4–5 times. In comparison with metal structures, the cost is significantly reduced and the steel consumption is reduced by a factor of 2–3 with a slight increase in weight. Currently in our country the use of tube concrete structures is not widespread due to insufficient study of their work under various influences. The tube in tube concrete structures simultaneously plays the role of a shell, as well as longitudinal and transverse reinforcement. For a classic tube concrete, the tube is able to perceive the resulting forces from different angles and in all directions. Concrete in the plastic tube, being in conditions of triaxial compression and withstands stresses considerably exceeding the cube and prism strength of concrete. In such structures, the tube prevents the formation of microcracks in the concrete core.

• Periodical: Materials Science Forum (Volume 974)
• Pages: 589-595
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.974.589
• Online since: December 2019
• Authors: Alexander V. Dolzhenko*, Andrey E. Naumov, A.V. Klyuev, N.A. Simonov
• Keywords: Bending, Plastic Tube Concrete, Strength Calculations of Building Structures, Tube Concrete

References

[1] K. Sakino, H. Nakahara, S. Morino, I. Nishiyama, Behavior of centrally loaded concrete-filled steel-tube short columns, J. Struct. Eng. ASCE. 130 (2) (2004)180-188.

DOI: 10.1061/(asce)0733-9445(2004)130:2(180)

[2] S.P. Schneider, Axially loaded concrete-filled steel tubes, J. Struct. Eng. ASCE. 124 (1998) 1125-1138.

DOI: 10.1061/(asce)0733-9445(1998)124:10(1125)

[3] C.S. Huang, Y.K. Yeh, G.Y. Liu, H.T. Hu, K.C. Tsai, Y.T. Weng, S.H. Wang, M.H. Wu, Axial load behavior of stiffened concrete- filled steel columns, J. Struct. Eng. ASCE. 128 (9) (2002) 1222-1230.

DOI: 10.1061/(asce)0733-9445(2002)128:9(1222)

[4] B. Uy, High-strength steel-concrete composite columns for buildings, Struct. Build. 156 (2003) 3-14.

[5] A. Dolzhenko, A. Naumov, A. Shevchenko, Bearing capacity and rigidity of short plastic-concrete-tubal vertical columns under transverse load, IOP Conf. Series, Materials Science and Engineering. 327 (2018).

DOI: 10.1088/1757-899x/327/4/042024

[6] A.V. Dolzhenko, A.E. Naumov, A.V. Shevchenko, N. Stoykovich, Numerical researches of the stressedstrained state of plastic tubed concrete pier under central compression load, Bulletin of BSTU named after V.G. Shukhov. 10 (2018) 23–32.

DOI: 10.12737/article_5bd95a716cf0c5.55926144

[7] A.V. Dolzhenko, A.E. Naumov, A.V. Shevchenko, N. Stoykovich, Influence of the tangential forces of friction on stressed-deformed state of polimer concrete pipe of centrally compressed short rod. Bulletin of BSTU named after V.G. Shukhov. 12 (2018) 42–51.

DOI: 10.12737/article_5c1c99553a7828.01508345

[8] I.R. Seryh, E.V. Chernyshova, Science-intensive technologies and innovations: Jubilee International scientific-practical conference dedicated to the 60th anniversary of BSTU named after V.G. Shukhov, XXI scientific readings. Belgorod State Technological University named after V.G. Shukhov. (2014) 112-115.

DOI: 10.15863/tas.2015.01.21.24

[9] L.K. Luksha, Strength of tube-concrete, High, Minsk, (1977).

[10] P.S. Sanzharovsky, Theory and calculation of the strength and stability of structural elements from steel tubes filled with concrete, (2000).

[11] A.P. Filin, Elements of the theory of cases, Ed. 2nd., Stroiizdat, Moscow, (1975).

[12] V.A. Snigireva, G.L. Gorynin, The nonlinear stress-strain state of the concrete-filled steel tube structures. Magazine of Civil Engineering. 83 (7) (2018) 73–82.

[13] A.R. Rzhanitsyn, The theory of calculation of building structures for reliability, Stroiizdat, Moscow, (1978).

[14] N.I. Karpenko, General models of reinforced concrete mechanics. Stroiizdat, Moscow, (1996).