Search results

The fabrication of AlTiB phases and the grain refinement of Al alloys by adding this phase were aimed.
This means that Ti and B takes place in Al matrix to form alloys and intermetallic compounds as seen from XRD results.
Xu, Effect of La2O3 in the Al–P–Ti–TiC–La2O3 modifier on primary silicon in hypereutectic Al–Si alloys, Journal of Alloys and Compounds, (2006)
Shen, Effects of hydrogen loading and type of titanium hydride on grain refinement and mechanical properties of Ti–6Al–4V, Journal of Alloys and Compounds, (2014)
Liu, Grain refinement limit and mechanical properties of 6063 alloy inoculated by Al–Ti–C (B) master alloys, Journal of Alloys and Compounds, (2014)

Heusler alloys are intermetallic compounds formed in two combinations: Full-Heusler (X2YZ) and Half-Heusler (XYZ).
These compounds are classified as intermetallic compounds, and their intriguing atomic arrangements have sparked curiosity within the scientific community.
This article aims to forecast the specific combination of elements that will result in Heusler alloys exhibiting shape memory properties.
Heusler Compounds: Categorization and Structural Considerations Heusler alloys encompass a wide range of applications, prompting extensive global research that continues to advance in current studies.
Journal of Alloys and Compounds, 921, 165984

The results indicate that the microstructures of the as cast alloy involve α-Al matrix, Al/Al2CuMg eutectic structure, Al7Cu2Fe, Al7Cu4Ni and Al9FeNi compounds.
The tensile test results indicate that the alloy at elevated temperature(200℃) displays superior tensile strength due to the presence of the thermally stable Al7Cu2Fe, Al7Cu4Ni and Al9FeNi compounds.
The tensile test results indicate that the Al-Cu-Mg-Fe-Ni alloy has better strength than the Al-Cu-Mg alloy at elevated temperature(200℃) due to the presence of Al7Cu2Fe, Al7Cu4Ni and Al9FeNi compounds.
Journal of alloy and compounds, Vol. 343 (2002), p. 77
Journal of alloy and compounds, Vol. 352 (2003), p.84

Alloys were produced by powders metallurgy.
It is also know, that a decrease in the particle size (< 1µm) of the intermetallic compounds is reflected as an increase of the alloy mechanical resistance.
The aim of this work is to fabricate Al-Ni alloys with different nickel contents by powder metallurgy and to evaluate the effect of the nickel concentration on the microstructure and mechanical properties of the resulting alloys.
With the help of the scanning electron microscope were taken photographies in different samples to verify the formation of intermetallic compounds.
§ The formed intermetallic compounds seem to be always located in intergranular zones of the matrix

Materials and methods 2024 Al alloys are produced in Romania at S.C.ALRO S.A.
By aspect of compounds arrangement, cooling was done quickly enough.
Ellipsoidal compounds or those rounds, black represents strengthener Mg2Si compound.
Fe element distribution indicates its major presence in compounds, and very little in the matrix alloy.
Bratu, Experimental researches on the corrosion behavior and microstructural aspects of heat treated Al-Zn-Mg-Cu alloys, International Journal of Energy And Environment, (4) 4 (2010) 122-130

Syntheses of the Ni3Ti, NiTi, and NiTi2 compounds by mechanical alloying C.B.
The Ni3Ti, NiTi, and NiTi2 compounds were synthesized after milling for 30h.
Different milling times were used to synthesize the binary compounds.
According with the XRD results, singlephase alloys were obtained only.
The Ni3Ti, NiTi, and NiTi2 compounds were formed after milling for 30h.

The aim of this work was to describe the microstructure of several possible hydrogen-storage alloys (Mg-Ni, Mg-Cu, Mg-Cu-Al, Mg-Zn) and to investigate the behaviour of these alloys during the electrolytic hydrogen saturation.
Results and discussion Microstructure of the investigated alloys is given in Fig.1.
Li, Journal of Solid State Chemistry 178 (2005) 2211-2217
Drulis, Journal of Alloys and Compounds 429 (2007) 316-320
Kim, Journal of Alloys and Compounds 312 (2000) 60-67

Erbium actively react with aluminium and forming intermetallic compounds in the eutectic and in highly disperse form.
Master alloys prepared by aluminothermic reduction of chloride-fluoride melt used instead of master alloys prepared by direct alloying process to reduce cost of production of alloys and energy-efficiency while adding of erbium to aluminum alloys, which is due to the production technology of pure metals from compounds.
Morri, Er addition to Al-Si-Mg-based casting alloy: Effects on microstructure, room and high temperature mechanical properties, Journal of Alloys and Compounds. 708 (2017) 1234-1244
Liu, Grain refinement in an Al–Er alloy during accumulative continuous extrusion forming, Journal of Alloys and Compounds. 680 (2016) 283-290
Nie, Precipitation hardening and recrystallization behavior of Al-Mg-Er-Zr alloys, Journal of Alloys and Compounds. 687 (2016) 143-151

In this scenario the present work aims at the fabrication and characterization of the microstructure and the mechanical properties of the as–cast Ti-12Mo-25Nb alloy.
The objective of the present work is the production and characterization of a β -Ti single-phase alloy with a higher concentration of Nb aiming for better properties, particularly lower elastic modulus.
Moeq., the titanium alloys are classified as β-metastable.
Pan: Journal of Alloys and Compounds Vol. 768 (2018), p. 697
Nunes: Journal of Alloys and Compounds Vol. 536 (2012), p.

In this study, the FeS2 fine compound powders for active material were made by mechanical alloying using the Spex mixer mill.
After 15 hours high mechanical alloyed powders were fractured to fine compound p was about 0.98um.
Liu: Journal of Alloys and Compounds 390 (2005) 255-260
Lee, Jai-Young Lee and Hyo-Jun Ahn: Journal of Alloyd and Compounds 349 (2003) 290-296
[3] Nam Hoon Goo, Jung Hoon Woo and Kyung Sub Lee: Journal of Alloys and Compounds 288 (1999) 286-293