Search results

Fig. 1.
Table 1 shows the results of fire tests of coatings based on sols 10-14% concentration.
№ sample SiO2 concentration, [%] Number of layers of coating Charging start time, [sec] The area of charring the reverse side at 8 sec Time of the beginning of destruction, [min] Area of destruction, [mm2] 20 not impregnated - 7 632 1,02 completely burned 21 10 1 6 50 1,36 final decay 22 2 8 22 1,41 23 3 15 0 5,39 24 12 1 7 277 1,40 25 2 9 89 5,18 26 3 10 0 2,38 27 14 1 7 299 1,48 28 2 8 50 2,12 29 3 9 0 1,47 Table 1.
References [1] J.
Emen, The use of sol-gel method for obtaining fire-resistant elastic coatings on cotton fabrics, Materials Science Forum. 1038 (2021) 468-479

Lemma 1 [55,56].
Table 1.
Chaos. (2013) 1-7
Wang, Generalized finite time synchronization between coupled chaotic systems of different orders with unknown parameters, Nonlinear Dyn. 74 (2013) 479-485
(CISIA 2015), Atlantis Press, 2015, pp. 479-482

This new process is schematically shown in Fig.1.
Fig.1 New process for making Ni (and Mn) free stainless steel.
References [1] R.
Forum Vol. 475-479 (2005), p. 2317
[13] Mitsuo Niinomi, Toshikazu Akahori, Tsutomu Takeuchi, and Shigeki Katsura: Materials Science Forum, Vols. 475-479 (2005), p. 2303

Fig.1 shows the CV curves of DA at different scan rates (from 10 to 200 mV/s) with the purpose of investigating whether the redox behaviour of DA was due to diffusion or adsorption on Nafion/Qu/G/GCE.
Fig.1.
Fig.4. shows the DPVs of 1.0×10-4 mol/L DA and 1.0×10-4 mol/L DA +1.0×10-3 mol/L AA+1.0×10-3 mol/L UA in pH 6.8 PBS, respectively.
References [1] Y.
Bioelectron. 35 (2012) 479-483

However, it offers a low degradation rate of pollutants [1].
References [1] A.
Vol 2(1), (2014) 5557-572
Kendall, Selection of Suitable Dispersants for Aqueous and Titania Powders using Acoustophoresis, Journal of the European Ceramic Society 19 (4)(1999) 479–488
Technology 36:1 (2006)

Table 1.
(Lr = 1) × Lr (N −1) / 2 N for 1 ≤ Lr < Lrmax (12) N and Lr max are as in Eqns. (9) and (10).
The plasticity correction function, f(Lr), is defined in the mismatch option as follows: f(Lr) = 1+ 1 2 Lr     −1/ 2 × 0.3 + 0.7exp(−µM Lr 6) [ ] for 0 ≤ Lr ≤1 (13) f(Lr) = f (Lr =1) × Lr (N M −1)/ 2NM for 1 < Lr ≤ Lr max (14) where µM = M −1 (FYM /FYB −1) /µW + (M − FYM /FYB) /µB < 0.6 else µM = 0.6 (15) µB = 0.001 EB σYB < 0.6 else µB = 0.6 (16) µW = 0.001 EW σYW < 0.6 else µW = 0.6 (17) Lr max = 1 2 1+ 0.3 0.3− NM       (18) where M=σYW/σYB is the mismatch factor defining the ratio of weld (σYW) to base (σYB) metal yield strengths.
Webster (Guest Editor), "European Structural Integrity Assessment Procedure - SINTAP", Special Issue of the Engineering Fracture Mechanics, 67 (2000) 479, pp. 481-668
Mech., 67 (2000) 479, pp. 529-546

Liu Wei [1] and Ge Dawei [2] have shown that the solution treatment should meet the conditions of rapid temperature rise.
Standard steel sheet tensile specimens are shown in Fig. 1.
Table 1 Chemical composition of 20LH5 stainless steel Ingredient C Si Mn Ni Cr Cu N Mass fraction (%) 0.0843 0.52 10.35 0.6174 14.04 0.88 0.18 Fig. 1 Standard tensile specimen of 20LH5 stainless steel (Unit: mm) Experimental Methods
(1) Material phase diagram simulation and solution treatment process formulation.
References [1] Liu, Wei.

It is known that superior performances of superalloys and their degradation are closely related to the change in its microstructure as indicated in Fig. 1.
Method of calculation Fig. 1.
The total strain actually agrees with the experimental creep strain at the beginning of the secondary creep stage; see Fig. 1.
References [1] J.K.
Forum, Vol. 475-479(2005), p. 619

At Tsub= 1073 K, the value was 1.4x10 -1 Ωm.
At PO2= 80 Pa, the value was 1.5x10 -1 Ωm.
The resistivity of these BRO films were 1.4x10 -2 Ωm.
References [1] A.
Forum Vol. 475-479 (2005), pp.1209

Measured mechanical properties of steel in table 1.
Fig. 1.
Model structure size and reinforcement plans (unit: mm) Table 1.
References [1] Ping Chen.
ACI, Dec 1955:455-479 [3] Hongnan Li, Bing Li.