Optimal Deformation Hardening in Lead Base Anodes for Copper Electrowinning for an Appropiate Working Life

Abstract:

The lead base anodes (Pb-0.07% Ca-1.3% Sn) of 6 mm thick have limited working life due to their loss of thickness and corrosion during the electrowinning process. If this loss of thickness is combined with a low yield stress of the anodes, these are much more likely to suffer premature deformations and distortions in cells. The aim of this study is to optimize the deformation hardening of the anodes, so as to achieve the best combination of yield stress and corrosion resistance to increase their working life. To achieve this the aged anodes were cold rolled to different area reductions from the standard 50% to 75%. To each one of these rolled anodes its yield stress was determined by plane compression tests, their grain sizes was measured by means of optical microscopy and their corrosion rate was determined by coulomb metric assays in a cell using an electrolyte concentration of sulfuric acid of 180 g/l and a oxidation current density of 300 A/m².It was found that the maximum yield stress of the anodes increases from 58 MPa to 64 MPa when cold reduction goes up from 50% and reach 70% . Regarding the corrosion rate, the maximum and minimum values were 0.33 mm/ year and 0.30 mm / year, i.e., with no significant differences between the different rolled anodes. Based on the above results it is concluded that an increase in the working life of the anodes is obtained simply by giving them greater cold rolling deformation from the current 50% to 70% of area reduction.

• Periodical: Materials Science Forum (Volume 879)
• Pages: 284-288
• DOI: https://doi.org/10.4028/www.scientific.net/MSF.879.284
• Online since: November 2016
• Authors: Carlos Camurri*, Claudia Carrasco, Yazmín Maril
• Keywords: Corrosion Rate, Grain Size, Lead Base Anodes, Yield Stress

References

[1] C. Camurri, M. López, A. Pagliero, F. Vergara, F, Materials Characterization. 47, (2001), pp.105-109.

[2] C. Camurri, E. Araneda, A. Pagliero, J. Dille, Materials Science Forum, Vol. 475-479 (2005), pp.2631-2634.

DOI: 10.4028/www.scientific.net/msf.475-479.2631

[3] C. Camurri, A. Pagliero, M. López, F. Vergara, Normalización de calidad y comportamiento de ánodos. En Workshop, Calama, Chile, (2002).

[4] Camurri C, Araneda E, Pagliero A Mejora en las propiedades mecánicas de ánodos base plomo utilizados en la electroobtención de cobre, En SAM/CONAMET, Bariloche, Argentina, ( 2003).

DOI: 10.3989/revmetalm.2003.v39.i1.315

[5] Camurri, C, López M, Pagliero, A, Vergara F, Deformaciones en ánodos base plomo utilizados en la electroobtención de cobre. En IBEROMET VI, Barcelona , España, (2000).

[6] Rossi F, Lambertin L, Delfaut-Durut L, Maitre A, Vilasi, M, Journal Power Sources, pp.296-300, (2009).

DOI: 10.1016/j.jpowsour.2008.11.049

[7] Maitre A, Bourguignon G, Fiorani JM, Ganbjaja J, Steimetz J, Materials Science Engineering A, pp.233-242, (2003).

[8] Muras j, Journal Power Sources, pp.119-122, (1995).

[9] H. Othani, Journal Phase Equilibria. Vol 16, (1952), p.317.

[10] Pérez F, Camurri C. Carrasco C, Colàs R, Materials Characterization, pp.62-68, (2012).

[11] Camurri C, Carrasco C, Prat O, Mangalaraja R, Pagliero A, Colas R, Materials Science and Technology, pp.210-214, (2010).

DOI: 10.1179/174328409x443245

[12] Winand R. , Métallurgie, Vol Xvii, N°2, p.56, 819789.

[13] Mao GW, Larson JG, Rao P Journal Electrochemistry Society, pp.11-17, (1973).

[14] Prengaman D, Anodes for Electrowinning, ed. Robinson & James, AIME, pp.49-57, (1984).

[15] Prengaman D, Siegmund A Improved copper electrowining operations using wrought Pb-Ca-Sn anodes Copper 99, Phoenix, Arizona, pp.1-11, (1999).

[16] Howard AM, Willihnganz E, Electrochemical Technique, pp.370-374, (1968).

[17] Young Ja, Barclay JB, Cast lead calcium tin grids for maintenance free batteries , Proceeding 85 th Batterry Council International Meeting, p.37, (1973).

[18] Rose MV, Young JÁ, Lead calcium (tin) alloys. Properties and prospects, 5 th International lead Conference Paris, (1974).

[19] Caldwell TW, Sokolov US, Power Sources, pp.73-79, (1975).