Search results

The final yield for all compounds was about 30 - 50%.
Xray powder diffraction showed that these compounds were amorphous.
Due to the presence of CoII as heteroatom all compounds were blue coloured.
The SEM image of supported CoW11Co (Fig. 4a) is different from those of the Ln compounds.
Trindade: Journal of Alloys and Compounds Vol. 374 (2004) p. 344

The aim of this paper is to study on feed rate, towards surface roughness and Built Up Edges(BUE), and drilling of aluminium alloys used in aircraft component.
Hence, optimal results are achieved by considering all relevant factors when drilling aluminium alloys.
Staley: Application of modern aluminium alloys to aircraft.
Ezugwu: Machining of aluminium alloys: A review.
Marcos : Analysis of the evolution of the Built-Up Edge and Built-Up Layer formation mechanisms in the dry turning of aeronautical aluminium alloys.

Introduction The advancement of technology makes it necessary to seek new solutions aimed at product effectiveness and quality improvement.
The aim of the present work is to study and achieve the controlled synthesis of nanocrystalline magnesium embedded in a carbon matrix by using Thermionic Vacuum Arc technology.
The film is compound by nanoparticles very smoothly distributed, indicated by the presence of the well - defined rings by electron diffraction.
O. lafsson, Journal of Alloys and Compounds, 446–447 (2007) 530–533

Introduction The nickel and nickel based alloys are used in the wider range of applications as corrosion resistant alloys, resistance heating elements, controlled expansion alloys and elevated temperature creep resistant alloys.
The Nickel-molybdenum alloys are better corrosion resistant in reducing conditions than nickel or cupronickel alloys [1-5].
The aim of the paper is the study of the weldability of Nickel sheets using an electron beam welding method.
Sowards: Weldability of Nickel-Base Alloys.
Fu: Hot deformation behavior and hot working characteristic of Nickel-base electron beam weldments, Journal of Alloys and Compounds, Volume 584, 25 January 2014, Pages 494-502 [11] Y.

The LCMO compound has been synthesised using sol-gel route.
Therefore, this project is aimed to investigate the structural and electrical properties of La0.7Ca0.3MnO3 (LCMO) nanocomposites incorporated with the different ratios of α-Fe2O3 nanoparticle.
Hence, the calcination of the compound was performed at 500°C and then sintered at 800°C to obtain the single phase of LCMO compound.
Liu, Electrical transport properties and enhanced broad-temperature-range low field magnetoresistance in LCMO ceramics by Sm2O3 adding, Journal of Alloys and Compounds 790 (2019) 240-247
Ferromagnetic compounds of manganese with perovskite structure, Physical Review 82 (1951) 403

Behavior of metal alloys in the semisolid state.
Effect of casting imperfections on fatigue life of 319-F and A356-T6 Al-Si casting alloys, Materials Science & Engineering A, 2008, 473: 65-75
Journal of Materials Science & Technology, 2012, 28: 946-950
Journal of Alloys and Compounds, 2009, 473: 133-138
Journal of Materials Processing Technology, 2007, 189: 182-191

The aim of this study is to compare the properties of porous cordierite produced by different amount of corn starch including pore structure, distribution and shape.
Journal of Alloys and Compounds, 487, 631-638, (2009)
[3] Ewais E.M.M., Ahmed Y.M.Z., Ameen A.M.M., Preparation of Porous Cordierite Ceramic Using A Silica Secondary Resource (Silica Fumes) for Dust Filtration Purposes, Journal of Ceramic Processing Research, Vol. 10, No. 6, pp. 721-728, (2009)
[6] Gregorova E., Pabst W., Bohacenko I., Characterization of Different Starch Types for Their Application in Ceramic Processing, Journal of the European Ceramic Society, 26, 1301-1309, (2006)

The nature of the interstitial phases is intermediate between real metal and covalent compounds.
Series: Journal of Physics: Conf.
Polyakov et al., The influence of non-vacuum electron-beam facing on the structure of Ti-Ta layers formed on the surface of VT1-0 alloy, IOP Conf.
Skeeba et al., Influence of W addition on microstructure and mechanical properties of Al-12%Si alloys, Materials 12(6) (2019) 981
Le Thanh, On regularities of destruction of impactor material at single blows, Journal of Mining Institute 233 (2018) 508-512.

Pulse Power Supply Transistor-RC compound pulse power supply is applied in the paper and a group of blasting capacitances is connected between two polarities in parallel.
Because free carbon content is high it is easy to form titanium carbide in kerosene so that it is difficult to machine Ti alloy.
In contrary, because free carbon content in de-ionized water is low it is easy to machine Ti alloy and machining efficiency is higher.
Aiming at a cylinder workpeice, the positioning method illustrated in Fig.5 is applied under the foundation that tangent hole accuracy is analyzed,.
Rahman: JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, Vol. 209 (2009), p.1706-1716 [3] Zhu Yuhua, Wei Hongyu, Zhao Wanshen.

The important compounds in the plant extract are hydroxyl and carbonyl groups which act as reducing agent as well as stabilizing agent.
Most of the plants contain an ample of free radical scavenging molecules such as phenolic compounds, nitrogen compounds, vitamins, reducing sugar, terpenoids and some other metabolites that are rich in antioxidant activity [2].
Phenolic compounds are well-known phytochemicals found in all plants.
However, since Folin-Ciocalteu technique is simply a redox reaction, it is actually quantify not only phenolic compounds but also other compounds that have reducing power such as amino acids, carbohydrates, ascorbic acids and others [10].
Extraction occurred as solvent diffused into plant tissues and solublized compounds with similar polarity [17].