Search results

And one of the most important factors influencing the performance is working pressure.
Thus it is necessary and imperative to figure out the relationship among the factors influencing depositing process.
And the most important among these factors are pressure, velocity, and temperature.
As the gauges has been given, there is another important constant factor would influence the measurement results: the installation site of the sensors could affect the accuracy of the measurement value.
Vol. 01 (2007), p.43-46 [4] LI Shi-Bin, Effect of Substrate Temperature on the Optical Properties of a-Si:H Films by RF-PECVD.

In this work it is shown how the microscopic residual stress state in 6061Al-15vol%SiCw composites can be modified by plastic strain and by isothermal annealing (the latter, affecting also the precipitation state).
They have improved mechanical properties with respect to those of the corresponding unreinforced metallic matrices and this improvement is achieved without a significant increase in weight.
Moreover, the (311) plane for fcc lattices is one of the less affected by texture between the low-indexed planes.
These results point out that the difference of CTE and the temperature drop are the most important factors determining the magnitude of the m-RS.
Since the latter are not affected by plastic deformation, the present result is expected.

The heat affected zone affected by PEMS is apparently uniform in Fig. 2 (b).
The other is that the mechanical effects caused by the PEMS give rise to the rotary motion of the liquid metal, generate strong mechanical erosion to the interface of the liquid and solid in the molten pool, interrupt the primary dendrite arm and reform fine crystal block [6].
It is because that B0 is the most influential factor to magnify the electromagnetic thrust in the pool.
It is because in a rotary magnetic field, the columnar grain refinement is prompted and tends to be uniformly distributed and the mechanical properties of the parts are also improved.
It mainly contains following aspects: (1) PEMS affects the heat affected zone of TA15 LMD obviously.

Moreover, the properties of large deformation resistance and poor ductility make the necking easy to occur and lead to tool damage during the titanium tube forming.
Material properties of TC4 see reference Literature [7-9].
As shown in Fig.6, when only the pressure die transfers heat to Ti-tube, afterheat affects the tube non-deformation zone; the effects of the mandrel transfer heat is similar to the situation of the pressure die and mandrel transfer heat together, afterheat affects the tube non-deformation zone little, and heating efficiency is high.
Table 1 Ф50×1×R75mm bending tool parameters Tool Groove dimensions (mm) Length dimensions (mm) Note (mm) Bend die 50 150（straight segment） bending radius 75 Clamp die 50 150 Pressure die 50 250 Wiper 50 128 Mandrel 47.6 202 mandrel extension length 6.5 Balls 47.6 18 (thickness) number 3 Take all factors including wall thinning, wall thickening, wrinkling, cross-sectional distortion multiple indices into consideration, the simulation results shows that, the reasonable bending velocity is 0.4rad/s, the matched pressure die velocity is 80%-110%.
Titanium material will appear complex changes of mechanical properties and other series of adverse effects.

However it has been found that the resulting resin properties are dependent on a complex set of factors including nano-filler size, shape, volume fraction and degree of dispersion as well as characteristics of the polymer matrix and filler-matrix interactions [5].
By careful selection of critical interrogation points within the RVE, a set of enhancement factors can be developed which cover the vast majority of critical load cases.
At run-time of the continuum simulation, only the MME algorithm needs to be updated to account for the new enhancement factors.
Ayewah, Improvements in mechanical properties of a carbon fiber epoxy composite using nanotube science and technology, Compos.
Enomoto, Mechanical properties of CFRP laminates manufactured from unidirectional prepregs using CSCNT-dispersed epoxy, Compos.

Table1 show the factors and their levels employed in the experiments.
Maybe this is due to act of the eggshell particles as nucleation centers (inoculation) and therefore improved mechanical properties.
Eggshells can be used to improve the hardness properties of aluminum metal 2.
Motgi, "Study on mechanical properties of Fly ash and alumina reinforced aluminum alloy (LM25) composite", IOSR-JMCE, Vol.7, pp41-46, 2013
Eckert," Effect of Particle Size on Microstructure and Mechanical Properties of Al-Based Composite Reinforced with 10 Vol.% Mechanically Alloyed Mg-7.4%Al Particles " Technologies, 4.37, 2016

INTRODUCTION In recent years, the SOI (silicon on insulator) which structure layer is Monocrystalline material has paid widespread attention in the study of the micro-mechanical devices.
Factors like wafer temperature, size of the release holes, and the thickness and amount of BOX layer to be etched determine the lateral etch rate, which was experimentally determined by measuring the undercut in the BOX layer after a certain amount of etching time.
Study of the Corrosive Property of Metal Electrode［J］.Chinese Journal of Sensors And Actu ators，2012，25（3）：326-328
In:Proceedings of Micro Mechanical Systems，IEEE， 1993，71-76
Study of the Factors Affecting the Sacrificial Layer’s Etching Rate[J].

The forming quality is the important factors to improve the performance of the gear shaft, but there are a lot of factors to influence the forming quality.
Test Factors and Level.
So choose module, number of teeth, rolling temperature and feed rate of mold as the main influence factors[6].
According to the metal material properties and process characteristics of cross wedge rolling, temperature range from 1000 ℃ to 1150 ℃.
(2) Comparison R of each factors, show that the four factors in order is B (module m), C (number of teeth z), A (temperature T), D (feed rate V)

Correlation analysis revealed that the dependence of microhardness on the factors under study is strong – the multiple correlation coefficient reaches value 0.999.
It describes the dependence of microhardness on the factors under study, which has the following form: Hμ=8087,7Ra-0,07 (3) Analysis of the obtained nonlinear regression dependence made it possible to reveal the value of the multiple correlation coefficient, which reaches the value 0.995.
Moscow: Mechanical engineering, 2003
Dispersion-hardened composite coatings with desired physical and mechanical properties.
Mechanical, operational and technological properties of electroplated coatings.

By contrast, electrochemical machining (ECM) with high machining speed and surface quality was not affected by blade materials strength, hardness, and toughness, physical and mechanical properties of restrictions [6-8].
There are many factors which affect the machining quality in ECM such as feed rate of tool cathode, electrolyte conductivity, the current density, the inter-electrode gap and so on.
Because the ECM process is very complex and often affected by some process factors,i.e. electrolyte flow field, electric filed, anode material dissolution and gap distributions.
There are two factors can impactdistribution, as shown in Fig.3, they are oblique feed angleof tool cathode and fixture angleof blade stock.
As mentioned above, the ECM process may effected by some unpredictable disturbances factors easily and in turn cause fluctuations.