Search results

The data obtained can be applied as an alternative method to utilize waste cement particles in the plastics industry.
When comparing the percentage reduction in the tensile strength of polypropylene filled with waste cement particles to polypropylene using compatibilizer and coupling agent but without waste cement particles, it is found that polypropylene filled with 10 phr of waste cement particles using PP-g-MA exhibits a reduction in tensile strength of 12.14%.
In contrast, using 3-aminopropyl triethoxysilane as the coupling agent results in a reduction of only 4.42%, which is a relatively small decrease.
In contrast, using the coupling agent 3-aminopropyl triethoxysilane results in a 51.43% reduction.
Smith: Data in Brife Vol. 39 (2021), 107534 [9] E.

The mesh was rebuilt at every time step, due to the extreme area reduction.
Mechanical Proprieties UTS and Area Reduction.
Each processing condition was simulated by means of complete thermo-mechanical FEM analysis (for detailed modeling data refer to [14]).
No strain data were available below 75 MPa, but it seems conceivable that the same correlation will remain valid until the critical pressure of 50 MPa formerly set, below which the true strain would necessarily fall to zero.
The considerable scattering of the data is the result of different facts: • The profiles were tested in the "as extruded" shape, namely with their thinning defect (the reduction of thickness with respect to the nominal one); • The higher the speed, the higher the thinning defect; in order to avoid this problem the area reduction was chosen as the best parameter to evaluate deformability; • Different conditions of preheating and speed determines different recrystallization of the profile and thus different responses to tensile test Nevertheless, the general tendency toward a decrease in deformability with process speed was clear and for this reason it has been reported here.

It was found that reduction of the crystallites size down to nanosize essentially increased the elasticity modulus at their fixed concentration.
The aim of this work consists in calculation of the elasticity modulus of a semi-crystalline polymer based solely on its chemical structure and the degree of crystallinity, with no resort to experimental data.
The proposed calculation scheme does not require the knowledge of any experimental data except for the chemical structure of the polymer.

The statistic data warns that the energy industry in Henan province faces some serious issues because of the oneness and limitation of the energy resources in Henan area and the local economy would be fatefully impacted if the increment speed of the energy supply cannot follow the increment speed of energy demand.
It stands at No.11 from the top in China. [2] So it will still remain the case to buy in the raw materials, energy products, equipment and technologies, such as crude oil, iron ore and etc. every year in Henan region. 2.2 Quick Development of the Local Energy Industry According to the data of 2008 the total primary energy production in Henan is 154.87million tons of SCE.
Energy conservation and emission reduction are related tightly with the survival and development of the industry, and a key point of sustainable development of local economy. [5] On the one hand we should timely expand the share of oil imports and increase the oil reserves; on the other hand we should give much effort on research for new technologies and products to replace the oil for the purpose of reducing the risk of over-reliance on oil. 3) To accelerate the development of diverse energy sources.
According to the authoritative estimates, if the proportion of high-tech products is increased by 1%, namely the proportion of high energy-consuming industries is dropped down by 1%, the corresponding reduction in energy consumption per unit of GDP shall be 1.3%.Optimizing the secondary industry is the precondition for realizing energy saving. [6] We have to reduce the proportion of the high energy-consuming industries in this region.
Energy Conservation and Emissions Reduction Strategies in Foundry Industry [J].

These metabolites could instantaneously engage in silver reduction to nucleate AgNPs and roleplay as capping agents to stabilise AgNPs.
Lethality assay data are available not only for seaweed-derived metallic NPs but also for organic and inorganic engineered nanomaterials [5].
The observed colour change indicates Ag+ reduction [2], suggestive of the reducing capacity of metabolites in the SWE.
It was suggested the high reaction rate favours in facilitating consumption of silver ions in the formation of nuclei, thus hindering secondary reduction events on the preformed particles.
The data herein provided evidence on the future development of AgNPs that integrates P. tetrastromatica in its formulation with distinct features, and a fundamental understanding of their potential environmental impact.

In view of savings in primary energy use and reduction of environmental impacts, power sources of future automobiles will shift from internal combustion engines to fuel cell engines.
One of the most promising pathways to produce and supply hydrogen is on-site hydrogen production from natural gas, which offers high total energy efficiency and substantial reduction of greenhouse gas emissions on the well-to-wheel basis.
Natural gas with steam Membrane module (Pd-based alloy) Catalyst a new concept of membrane reformer is expected to give dramatic efficiency increase and size reduction.
Through the demonstrative operation of this refueling station, technical issues under practical refueling service conditions have been identified and data have been collected and evaluated in view of environmental impacts, overall efficiency on the well-to-tank basis, safety issues, etc.
Engineering data and know-how for construction, operation and management of the hydrogen refueling stations have also been accumulated for the future hydrogen supply business.

The seismic behavior of frame by the filler walls consider the influence of the frame cycle which was caused by the filler wall’ stiffness simply, the cycle multiplied by a reduction factor of 0.6 to 0.7 according to the number of filler walls[2].
But we can find that the seismic performance of the filler walls to frame structures is very complex in the Wenchuan Earthquake, the method that multiplied by reduction factor to consider the effect of filler walls on seismic behavior of frame is incomplete.
So the stiffness should be multiplied by a reduction factor, and the factor is 0.2 according to the documentation [1].
From the model 3’s data analysis, we can find that setting appropriate shear walls in the weak layer has significant increased the layer stiffness and improved the bearing capacity of the weak layer.
Comparing the analysis data of the three sets, it can be found that the measures setting shear walls in the weak layer to deduce the weak layer’s failure are feasible.

It was confirmed that in addition to the SEM EDX data, hardness results also demonstrated the effectiveness of centrifugal slurry methods to fabricate CNT/ Al matrix FGMs.
(As a reference, pure Al data is also included.)
Fig. 11 shows mass reduction of samples of FGMs with the rotation speed from 150 to 450 rpm.
It can be seen that, in FGMs with the rotation speeds of 150, 250, 300 and 400 rpm, CNT-rich sides show lower mass reduction than CNT-poor sides, for which the reason is considered because in CNT-rich sides CNT was CNT scraped off the surface, which prevent scraping of Al, leading to low mass reduction of the samples.
Fig.11 Mass reduction of samples of FGMs with the rotation speed from 150 to 450 rpm.

This container provides iterators which algorithms use to access data, perform analyses, and control components.
Each component uses iterators to define the relationships with other components and the data stored in the container[7].
As indicated earlier, a circuit analysis program must efficiently manage large quantities of system and equipment data.
The iterators and linked lists compact the data storage and reduce algorithm execution time.Each graph trace represents a particular linked list tracing through the components of the circuit.
The container is used to exchange data among algorithms.

Thermocouples readings were recorded over time using an AT45xx multi-channel type data logger.
AT45xx multi-channel data logger and EZDO SP-216 solar power meter devices.
The experiment is repeated for the other cases, data is collected, and the results are compared as shown in Fig 4.
Schematic diagram of the test wall specimen and the distribution of the sensors, data logger, and PC connections.
Acknowledgment The researchers extend their thanks and appreciation to the Al-Diwaniyah tires factory for facilitating the required rubber crumb technical data.