Search results

Its processing is able to produce selective deposition and high structure quality thin films on large areas.
Liu et al. [2,3] and McDaniel et al. [4,5] employed a boundary-layer model incorporating a catalytic reaction to simulate the kinetics of CdTe deposition in a tubular reactor and studied the reaction chemistry of CdTe using on-line gas chromatography and numerical simulation.
Hicks, Chemistry of photo-assisted organometallic vapor-phase epitaxy of cadmium telluride, in: Journal of Crystal Growth, Vol.123, 1992, pp.500-518
Hicks, Chemistry of cadmium telluride organometallic vapour-phase epitaxy, in: Journal of Physical Chemistry, Vol.99, 1995, pp. 3574-3582

BaTiO3 has a tetragonal structure at room temperature.
Correspondingly, the dielectric property of BaTiO3 changes with its crystal structure.
Discussion In most cases, doped BaTiO3 shows a tetragonal or cubic structure.
Cheng, Temperature-dependent structure of a high-k (Ba,La)(Ti,Ce)O3 ceramic, Key Eng.
Vanderah, Structure analysis of the 6H-Ba(Ti, Fe3+,Fe4+)O3-δ solid solution, J.

However, the understanding of how anion size variations impact metal ion solvation structure remains limited.
Elevated concentration disrupts bonds between Li+ ions and water molecules, resulting in alterations in solvation structure.
In this strategy, changes in solvation structure arise due to interactions between anions and cations.
This shift is attributed to the trapping of free water molecules within the solvation structure of Li+ ions at higher concentrations.
Xu, “Water-in-salt” electrolyte enables high-voltage aqueous lithium-ion chemistries, Science 350 (2015) 938-943

Thus, perovskite structure materials containing lanthanum have been widely studied as electrodes for solid oxide fuel cells (SOFCs), due to its electrical properties.
In this work was investigated the obtain of the perovskite structure LaCr0.5Ni0.5O3, by Pechini method, and its suitability as SOFC anode.
Mcintosh: Journal of Materials Chemistry Vol. 21(2011), p. 7443

When the indenter pushes to the new structure again, the force of the ram becomes large accordingly.
Because different crystal planes will form different structures in the pressing process.
The reason of hardening is that the new structure produced by the first nanoindentation changes the performance of the original structure.
Mayank, Comparing Atomistic Machining of Monocrystalline and Polycrystalline Copper Structures, J.
Tersoff, Modeling Solid-state Chemistry: Interatomic Potentials for Multicomponent System, J.

The influences of substrate etching on the morphology and structure were investigated by scanning electron microscopy, X-ray diffraction, Raman microscopy, and photoluminescence spectrum.
The morphology and crystalline structure of the samples were examined by the field emission scanning electron microscope (FE-SEM, SIRION, FEI Company) and the X-ray diffractometer (XRD, D8 Advance, Bruker Axs) with Cu-Kα radiation (λ = 0.15406 nm), respectively.
The growth mechanism ZnO nanorods with tips could be based on conventional growth model of solution chemistry [7].

China a*sarkeeva.e@inbox.ru, babramovamm@yandex.ru, cigorvalexandrov@yandex.ru Keywords: Сopper alloys, severe plastic deformation, structure, properties.
Results and Discussion The structure is uniform in the initial state, an average grain size is 140 ± 8 μm.
In the initial state, low tensile strength is 225 MPa (Table 1) and high plasticity is 62% (Fig. 2) as the structure is coarse-grained.
Alexandrov, Bulk nanostructured metal materials: preparation, structure and properties (Akademkniga, Moscow, 2000) [5] R.K.
Landolt-Börnstein - Group IV Physical Chemistry, Springer Berlin Heidelberg; V 11C2 (2007)

Halléna a Royal Institute of Technology, KTH, ICT, Electrum 229, Kista, Sweden b University of Helsinki, Department of Chemistry, P.O.
Multilayer structures were deposited by AlCl3 and varying ammonia and water at 500 oC [8].
This peak corresponds to the 002 direction of AlN and its intensity depicts that the AlN has a polycrystalline structure.
However, it was observed that the thickness of the deposited layers did not have any effect on the structure of AlN.
The dielectric properties of AlN and its combination with Al2O3 have been electrically evaluated by preparing MIS structures.

This powder has very fine dendritic-shaped particles with an inherent sub-micron grain-structure.
On the one hand, it may lead to full consolidation at lower pressures and shorter times, due to easy hot-flow of ultra-fine globular grain structures.
Compaction, Chemistry and Tensile Results A specialized vacuum hot press (VHP) unit, developed at the University of Dayton (UD) for producing magnets with nano-scale grains [10] was used for compaction.
This way, a fine powder grain structure may experience only limited coarsening during the hot compaction.
The ITP powder is a dendritic shaped powder with a micron-size globular grain structure. 2.

In order to analyze the structure of the WPC there was used a computer microtomography, one of the recent non-destructive methods for studying the bulk structure of composites using X-ray radiation.
Multidec (Multiplast, Russia) and Terrapol (Russia) terrace boards were chosen as the structures based on PE.
The most homogeneous structure is demonstrated by the WPC – PE and WPC – PVC compositions.
Mechanics, Resource and Diagnostics of Materials and Structures (MRDMS-2016) AIP Conf.
Russian Journal of Applied Chemistry. 2016 May 1;89(5):805-8.