Search results

Shein, Polymeric composite materials in railway transport of Russia (review), Scientific and Technical On-line Journal “Trudy VIAM”. 7 (43) (2016) [in Russian]
Uzdensky, Refractory polymeric materials (compositions and composite concentrates), The journal “Plastics”. 2 (2003)
Berlin, Combustion of polymers and materials with reduced flammability, Soros journal review. 9 (1996) 57-63
Younis, Effect of mineral fillers on the wetting of water-based polymer dispersions, IOP Conference Series: Materials Science and Engineering. 708 (1) (2019) 012103
Perez, The study of polymer materials by mechanical spectrometry, Polymer Science. 40 (1) (1988) 102-135

Material and Methods In order to measure the value of each sample, the materials and method were discussed in this section.
Hötler, “Degradation of Cellulose Acetate-Based Materials: A Review,” J.
Ash, “Biodegradable Plastics Based on Cellulose Acetate,” Journal of Macromolecular Science, Part a Pure and Applied Chemistry, vol. 30 (9), pp. 733-740
Lamble, “Ozone Uptake Rates and Secondary Product Emission of Green Building Materials,” Master.
Missouri University of Science and Technology, 2011

But it can only be used in special materials which τ0=2σtσc/(2σt+σc).
The results can be used in different materials and they can be used to fully utilize the potential of the strength of materials compared with other formulas.
And the formulas in this article can be used in different materials.
Journal of Chongqing University(Natural Science Edition), 2003, 26(11): 109-112
Journal of Chongqing University(Natural Science Edition), 2004, 27(9): 133-136

So this study mainly uses the temperature of liquid phase first formation, the temperature of liquid phase complete formation, the free flow temperature of liquid phase, liquid production as the main liquid formation characteristics, analysis of the effect of the grain size of raw materials and the chemical composition of minerals on mineralization characteristics.
The effect of the grain size of raw materials on mineralization With different particle size, the behavior of iron ore in sintering process is different.
Influence of Properties of Fluxing Materials on the Flow of Melt Formed in the Sintering Process.
Journal of University of Science and Technology Beijing, 2005 ,27 (3):291-293
Iron and Steel,1999,34:111 [5] Wu Shengli, et al., New Concept of Iron Ores Sintering Basic Characteristics, Journal of University of Science and Technology Beijing, 24(3)(2002):254-257

Introduction On one hand, the exploitation of mineral resources provides a lot of raw materials for the development of national economy and promotes economic development, on the other hand it has a huge impact on the ecological environment.
Table1 is material input coefficients of material inputs calculation of raw coal and the "*" represents the material input coefficient of steel and cement.
Acknowledgement This work was financially supported by Ten Million Talent Project of Liaoning(2012921075) and Liaoning Nature Science Founds(201102065) and New Century Talent Supporting Project of education ministry(NCET-11-0073).
Journal of Arid Land Resources and Environment, vol.27(2013), p.106-110.
Resources Science, vol.29(2007), p. 2-6.

Lavernia, “serial sectioning for 3D visualization and modeling of SiC particle reinforced aluminum composites”, Journal of Materials Science, 26 (1991) 1137-1156
Lavernia, “processing of discontinuously – reinforced metal matrix composites by rapid solidification”,Progress in Materials Science, 39 (1995) 317-409
Microstructure containing particles penetrable by dislocations”, Materials Science and Engineering, 13(1974) 141-157
Lai., “Recent development in the fabrication of metal matrix particulate composites using powder metallurgy techniques”, Journal of Materials Science, Vol. 29, (1994), pp. 1999-2007
Gungor, The Minerls, Metals and Materials Society, (1990)

As the high plasticity and toughness of stainless steel workpiece materials, the tool wear in cutting process is severe.
Zhang: Key Engineering Materials, (2006) No.315/316, pp.666-670
Liu: Journal of Materials Processing Technology, Vol. 189 (2007) No.7, pp.273-278
Wan,et al: Journal of South China University of Technology: Natural Science Edition, Vol. 36 (2008) No.4, pp.23-28.
Zeng, et al: Journal of South China University of Technology: Natural Science Edition, Vol. 29 (2001) No.6, pp.31-35.

Journal of Environmental Sciences, 2010, 30(4): 673-701.
Environmental Science, 2009, 30(6):1733-1737.
Journal of Environmental Sciences, 2008, 20 :1288-1293
Journal of Hazardous Materials, 2011, 193:1-9
Journal of Xi’an University of Science and Technology, 2008, 28(2): 336-339.

Abstract: The carbon composite materials with silicon carbide coating were prepared for aluminum electrolysis as inert anode.
WU: Journal of The Chinese Ceramic Society.
Aboelata: Journal of Magnetism and Magnetic Materials, Vol. 195 (1999), p. 667 [14] K.
Park, Materials cience and Engineering, Vol. 104 (2003), p. 9 [16] W.M.
WANG.: Journal of Anyang Teachers College, (2005), p.41

In this study, in order to address the problem associated with tradition solid reaction and high cost of raw materials for normal Pechini method, a modified approach using mixed starting materials of nitrates and readily available oxides have been utilized for the synthesis of 20 mol% Y-doped BaZrO3.
Liu: Materials Letters 73 (2012), pp. 198-201
Tompsettt: Journal of Fuel Cell Science and Technology Vol. 5 (1) (2008), pp. 1-4
Yamaguchi: Chemistry of Materials Journal, ACS Publications, Vol. 25, Issue 9 (2013), pp. 1483-1489
Irvine: Journal of Materials Chemistry 18(29) (2008), pp. 3414-3418.