Search results

In figure 4a, the entity of application A and the entity of application B constitute a map of the relationship between 1:1.
Property 1 Entity …… Entity …… …… Entity 1 …… a) b) Application A Application B Property 2 …… Property n Property 1 Property 2 Property m Property 1 Property 2 Property n Entity Property 1 Property 2 Property m Entity 2 Property 1 Property 2 Property m Fig.4 Configuration of information mapping With the flexible information technology, the integration between information systems transformed into the integration between adapters which dependent on the data itself and unrelated to the concrete information system, and the information mapping between adapters are realized by configuration in the information platform which independent of the concrete information system.
References [1] J F.
[4] J Cardoso: International Journal of Computer Science, Vol 1(2006), No. 1, pp. 8-21
[5] M Ioana, B Marco, C Stefano, et al: ACM Transactions on Internet Technology, Vol. 5(2005), No. 3, pp. 439-479 [6] S H.

Stress exponent n is equalled to 1/m, where m is the strain rate sensitive factor.
References [1] F.
Ceram. 1 (1986) 259-263
Technol. 12[1] (2004) 20-23.
Zhang, Superplastic extrusion of Al2O3-YTZ nanocomposite and its deformation mechanism, Materials Science Forum. 475-479 (2005) 2973-2976

Some of the design solutions are shown in Fig. 1.
Table 1.
If it is necessary to detail the survey, the areas are divided into squares measuring 1×1 m or 2.5×2.5 m.
References [1] Yu.M.
Duquennoi, Liquid flow through composite liners due to geomembrane defects: Analytical solutions for axi-symmetric and two-dimensional problems, Geosynthetics International. 6(6) (1999) 455-479

Table 1: Advantages and disadvantages of PP.
References [1] J.
Technol. 136 (2003) 1-6
Technol. 35 (2007) 468-479
Technol. 110 (2001) 1-9

Figs. 1 and 2 show the axial stress-strain, lateral-axial strain, plastic volumetric strain-axial plastic strain, and plastic dilation angle-axial plastic strain relationships of the specimens with the charactersitics summarized in Table 1.
Tab.1 Summary of test results used in Figs. 1 and 2 Group ID Study Dimensions of cylinder (mm) Lateral confinement flu,a (MPa) f’co (MPa) U30 Mirmiran et al. [25] ø152.5 × 305 1, 3, 5, 7 layers of Glass-FRP 4.0, 11.9, 17.1, 24.0 29.8 U64 Ozbakkaloglu and Vincent [26] ø152 × 305 1, 2, 3, 4 layers of Carbon-FRP 3.6, 8.0, 11.2, 15.2 64.2–65.8 (a) (b) (c) (d) Fig.1 Variation of: (a) axial stress-axial strain; (b) lateral strain-axial strain; (c) plastic volumetric strain-axial plastic strain; and (d) plastic dilation angle-axial plastic strain relationships with level of confinement and concrete strength (Group U30) Figs. 1(a) and 2(a), 1(b) and 2(b), and 1(c) and 2(c) respectively illustrate that the proposed model closely predicts the axial stress-strain, lateral strain-axial strain, and plastic volumetric strain-axial plastic strain behaviors of both NSC and HSC specimens.
This behavior corresponds to the contraction to expansion in Figs. 1(c) and 2(c).
References [1] Wu, Y.
Composite Structures, 95, 479–491

Some samples were irradiated with 1 MeV electrons at a fluence of 1×1015 /cm2.
Results and Discussion Fig. 1.
References [1] P.J.
A, 557 (2006) 479-489
Technol. 19 (2008) 102001-1-25

To evaluate these schemes are indispensable important segment [1].
For example, the evaluation parameter system of automobile diagnosis scheme as shown in Fig.1.
Table 1 representation three different schemes cost analysis of the automobile diagnosis system.
Define the capital input index of diagnosis system: (1-0.24 1-0.31 1-0.45).
Commun. 40 (2010) 475-479 (In Chinese)

b a Fig. 1 (a) Camphor, (b) Needle coke.
MOR , was calculated using Eq. (1) [1].
AFL was calculated using Eq. (2) [1].
References [1] F.
Sun, Microstructure and strength of needle coke modified ceramic casting moulds, Ceramics International, 40 (2014) 479-486

The various design parameters of the collectors are in Table 1.
The state properties and calculated exergy of the system corresponding to Fig. 1 are given in Table 2.
Schematic diagram of 500 kW Shiraz hybrid solar power plant Table 1.
References [1] Flavio G., Segio A., Silvia AN., Thermoeconomic evaluation of a gas turbine cogeneration system.
Part I, Progress in Energy and Combustion Science 29:479–485 (2003)

Fig. 1 Procedure of friction stir welding
Analytical Modelling Friction stir welding consists of the basic three operations of welding tool for objective materials as (1) rotate, (2) plunge and (3) move, as shown in Fig. 1.
The tool used in this experiment had a shoulder with 8mm-diameter and a probe with 3m-diameter and 1.7mm length.
On the other hand, clear differences appeared in the torque and the temperature; 3.88Nm, 454°C at the lower revolution of the tool and 2.41Nm, 479°C at the higher revolution.
References [1] W.M.