Search results

The results of the thermal inspection are presented in Fig. 1–10.
а b Fig. 1.
References [1] V.
Mater Sci.. 58 (2023) 474–479. https://doi.org/10.1007/s11003-023-00687-1 [6] I.
Energy Engineering and Control Systems. 10 (1) (2024) 1–6. https://doi.org/10.23939/jeecs2024.01.001

Materials and reagents Experiments using carbon nanotubes is Chengdu Institute of Organic Chemistry, Chinese Academy of production of high purity multi-walled carbon nanotubes, the basic parameters shown in Table 1-1.
References [1] S lijima.
China Nonferrous Metals, 2004,14 (3) 479-484
Foundry Equipment Research, 2003,1 (3) :9-11
Plating & Finishing, 2002,24 (1) :35-38.

According to [1] the relation between the average wear rate and the cutting speed is linear.
References [1] Y.
Horvath, Wear and Tool Life of CBN Cutting Tools International Journal of Advanced Manufacturing Technology  Volume: 20   Issue: 7   pp. 475-479   [5] A.
Technical Gazette 20, 1(2013), pp.21-26 [9] M.
Annals of the CIRP Vol. 45/1/1996 pp.77-82 [10] Y.

Recent Activities on Directional Solidification at the State Key Laboratory of Solidification Processing Lin Liu 1, a , Faqin Xie 1 , Jun Zhang1 , and Hengzhi Fu1 1 State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi'an 710072, P.
Fig.2 shows that Al, Ti and Ta are positive segregation elements for their segregation ratios are over 1, and W is the negative segregation element for its segregation ratio is less than 1.
The future trends of directional solidification may be in following aspects: 1.
References [1] F.
Forum, Vols.475-479 (2005), p. 665 [7] X.

Table 1.
The material was 1.2mm Ti-6Al-4V alloy sheet.
Example 1: A cover is shown as Fig.9 (a).
References [1] J.D.
Materials Science Forum Vol.475-479 (2005), p. 3033.

So countries of the world use various ways of hardening and study their influence on the properties of steel parts, including wear resistance in abrasive conditions [1-5].
As an example, a general view of the ploughshares before and after electric arc surfacing is given below (Fig. 1).
Figure 1 - General view of the ploughshares before surfacing (upper) and after surfacing (2 lower) In this way, almost any thickness of the deposited material can be obtained by processing both in one and several passes.
The hardness of the deposited material after processing and the nature of obtained structures are shown in Table 1.
C.; and other, The effect of microstructure on abrasive wear of a Fe-Cr-C-Nb hardfacing alloy deposited by the open arc welding process, Surface & Coatings Technology, Tome: 276, P.: 479-484 [10] Karip, E.; Aydin, S.; Muratoglu, M., A Study on Hardfacing Alloy Using Fe-Cr and Fe-B Powders, Acta physica polinica A, Tome: 128 (2B), P.: B160-B163 [11] Technological repair module for tools in the form of a ploughshare: utility model patent RU 139667 U1, MPK B23R 6/00 B25N 1/00 / A.P.

Also, the exponents for self-affine interfaces were verified according to the digital photography analysis[4]. 1.
In any time of t, select the list i randomly, then h (i, t + 1) can be got from h (i, t) (1) The average height of surface is defined as: (2) where L is the number of columns.
According to the KPZ equation[6], when the degree of dimension is 1, α=1/2 and β=1/3 as ballistic deposition. 2.
References [1] Goodchild, M.
[J] Remote Sensing ,41(12):1 479-1 486.

The ammonia was dropped into the mixed solution and continually stirred for 1 h.
After-calcination at 400 °C for 2 h, the corresponding XRD patterns are shown in Fig 1 (b).
Table 1 Calculated crystallite size of after-calcined In2O3:Sn nanoparticles with different Sn contents.
References [1] X.
Morante, Structural stability of indium oxide films deposited by spray pyrolysis during thermal annealing, Thin Solid Films 479, 2005, pp 38-51

Figure 1.
With probability 1- Pinter, a packet belongs to intra-segment traffic.
References [1] I.
Comm., Vol. 41, No. 1 (1993), pp. 110-120
Lin: The Designs of a Scalable Optical Packet Switching Architecture, Journal of the Chinese Institute of Engineers, Vol. 31, No. 3 (2008), pp. 469-479

As shown in table 1, at the same time interval the train through buttress ago A and B’s deposition [3].
When the train passes the bridge, the vertical acceleration peak is 1.785125g; the vertical acceleration peak of buttress in the train passes is 1.1375g.
As shown in Figure 7, when the train passes, the lateral acceleration extremism of buttress is 0.12258g, the maximum amplitude of 1.23126mm.
References [1] XIA He.Tapered Short Pile[M].Beijing:China Agriculture & Machine Press,1981
Acta Mechanica Sinica, 2001, 33(4): 479–491.