Search results

Fig.1 schematic diagram of SBR Materials A synthetic wastewater mainly consists of glucose and ammonium chloride.
H., Activated sludge nickel toxicity studies [J]., Journal of Water Pollution Control Federation, 1981,53, 1314-1322.
Journal of Hazard Material, 2008, 151(1) : 185-193
Journal of Biotechnology, 2002, 95(3): 249-256
Journal of Hazardous Materials, 2004, 106B:83-92

Through research on several different rib surface form and deep tensile properties of GFRP bar materials, different rib depth effect on the tensile properties of GFRP bar material was got.
The Preparation of GFRP Bars Some kinds of GFRP bars are manufactured in Chinese Education Ministry Research Center of Fiber Composite Materials and Structural Engineering, Zhengzhou University, their diameter is 18mm.
Seible, Use of FRP composites in civil structural applications, Construction and Building Materials, Vol. 17 6 (2003) 389-403
Guo, Grey relational analysis of parameters on bond between GFRP rods and concrete, Sichuan Building Science, Vol. 37 6 (2011) 10-13
Wang, Comparison and experimental study of bond behavior of deformed GFRP bars in different surface form, Glass Fiber Reinforced Plastic/Composite Materials, 2 (2007) 37-39

Advanced Materials, 2009. 21(21): p. 2233-2239. 5.
Journal of Materials Science, 2002. 37(18): p. 3855-3860. 8.
Materials Science and Engineering B-Solid State Materials for Advanced Technology, 2006. 131(1-3): p. 147-155. 10.
Journal of Sol-Gel Science and Technology, 2009. 52(3): p. 424-431. 11.
Journal of Materials Research, 1999. 14(2): p. 549-559. 13.

While brittle materials typically only absorb a small amount of energy before breaking, tough materials take in a lot of energy.
"Rolling, partial and full annealing of 6061 characterization of microstructure, tensile strengths and ductility, Materials Sciences and Applications. 7:9 (2016) 453-464
Kazimierz, P Tadeusz, Influence of the plastic properties of a material on the forming limit diagram for sheet metal in tension, International Journal of Mechanical Sciences 15:10 (1973)789-800. https://doi.org/10.1016/0020-7403(73)90068-4
Li, Effect of annealing on microstructure and mechanical properties of an Al–Mg-Sc-Zr alloy, Materials Science and Engineering: A 838 (2022) 142821. https://doi.org/10.1016/j.msea.2022.142821
Letters on Materials. 9:4s(2019) 556-560

Gilman: Journal of Applied Polymer Science Vol. 87 (2003), p.1329-1338
[5] Yusrina Mat Daud, Hussin Kamarudin, Che Mohd Ruzaidi, Azlin Fazlina Osman: Key Engineering Materials Vols. 594 (2014), p. 671-675
Dubois: Materials Science and Engineering: R: Reports Vol 28 (1-2) (2000), p. 1-63
Moet: Journal of Materials Science Vol 31 (13) (1996), p. 3589-3596
[10] Yusrina Mat Daud, Hussin Kamarudin, Che Mohd Ruzaidi, Azlin Fazlina Osman: Materials Science Forum Vols. 803 (2015), p. 58-62.

Ferraro, Journal of materials engineering and performance, 23 (2014) 611-621
Gholizadeh, Materials & Design, 50 (2013) 7-14
Wang, Journal of Materials Processing Technology, 207 (2008) 107-111
Zhang, Materials Letters, 57 (2003) 2523-2529
Doty, Materials Science and Engineering: A, 486 (2008) 241-252

Material & Heat Treatment, 2009, 38(22):14-18
Chinese Journal of Rare Metals, 2003, 27(1): 66-68
Effects of deformation aging on mechanical properties and electricity conductivity of Cu-Ni-Be alloy [J].Journal of Central South University(Science and Technology), 2010, 41(2):508-513
Journal of Material Science, 1974, 9: 398-408
Mechanical and Electrical proprieties and Microstructure in Cu-Ni-Be alloys [J].Journal of the society of material science, 2007, 56(6):531-536

The yield strength and the ultimate strength of the 3 materials are listed below.
Table 1 Yield strength and ultimate strength of the 3 materials in this case study.
Miner, Journal of applied mechanics 12 (1945) A159-A164
Tomita, Materials science and technology 7 (1991) 481-489
Phan, International Journal of Fatigue 29 (2007) 2060-2071

The deposited material was IN625 and the substrate material was AISI 316.
Klimova-Korsmik, Quality management of metal products prepared by high-speed direct laser deposition technology, Key Engineering Materials 684 (2016) 461-467
DebRoy, An improved prediction of residual stresses and distortion in additive manufacturing, Computational Materials Science, 126 (2017) 360-372
Zhang, Additive manufacturing of metallic components – process, structure and properties, Progress in Materials Science, 92 (2018) 112-224
Poprawe, Laser additive manufacturing of metallic components: materials, processes and mechanisms, International materials reviews 57, 3 (2012) 133-164

Lavernia, "Processing microstructure and fracture behavior of spray atomized and deposited aluminium -silicon alloy", Journal of Materials Science 32 (1999), 2835-2848
Tawfik, "Mechanical properties of rapidly solidified ribbons of some Ai-Si based alloys", Journal of Materials Science, vol 32, (1997), 2997-3000
Giese, "Thixoforming of an automotive part in A390 hypereutectic Al-Si alloy", Journal of Materials Processing Technology, Vol. 135, (2003), 271-277
Tsao, "Si coarsening of spray formed high loading hypereutectic Al-Si alloys in the semisolid state", Materials Science and Engineering A, Vol. 396, (2005), 263-270
Chaoa, "Dry sliding wear behaviors of Al-25Si-2.5Cu-1Mg alloys prepared by powder thixocasting", Materials Science and Eng.