Search results

The fibers added in the composites are desired to control the crack development of materials [1,2].
Materials and experimental methods Materials and Specimen preparation.
[7] Shilang Xu, Qinghua Li, Science in China Series E: Technological Sciences, 52(2)(2009), 363-378
[8] Qinghua Li and Shilang Xu, Science in China Series E: Technological Sciences, 52(6)(2009), 1648-1664
[13] Meral Oltulu, Remzi Sahin, Materials Science and Engineering A 528(2011) 7012-7019

Apart from conventional pigment applications, titanium dioxide is also found uses in the industrial sectors such as energy, pharmaceutical, environment and electronic materials [4-6].
This is beneficial to the appearance of composite materials and to the increase of the overall strength of the composites [16, 18].
Rosecbaum: Journal of the Minerals, Metals, and Materials Society, Vol. 34 (1982), p.76
Tenorio, et al: Materials Science and Applications, Vol. 5 (2014), p. 441
Furusawab, et al: Materials Chemistry and Physics, Vol. 105 (2007) No.2-3, p.162.

Yield strength, or the yield point, is defined in engineering and materials science as the stress at which a material begins to plastically deform.
In strength reduction method the strength characteristics of the rock mass and joints materials are reduced by a factor until the loss of stability or failure of the structure occurs.
The jointed material model of rock slope is intended to provide a simple, continuum model for materials containing a high density of parallel joint surfaces in some orientation.
Donze, International Journal of Rock Mechanics & Mining Sciences. 52(2012) 18-30
Green, Journal of Tribology. 127(2005) 343-354

The notion of defects in PPy bulk material has never been demonstrated before.
Gu, et al: Progress in Polymer Science, Vol.36 (2011) No.10, p.1415 [2]Dhibar S., Sahoo S.
:Journal of Applied Polymer Science.
Wan: Journal of Materials Chemistry, Vol.11 (2001) No.2, p.404 [16] J Bhadra, D Sarkar: Indian Journal of Physics, Vol.84 (2010) No.10, p.1321 [17] A.
Caruso: Advanced Materials, Vol.13 (2001) No.1, p. 11.

Kim, Carbon Nanotube-Reinforced Thermotropic Liquid Crystal Polymer Nanocomposites, Materials 2 (2009) 1955-1974
Efremochkin, Nano-additives for composite building materials and their environmental SAFETY, International Journal of Applied Engineering Research. 11 (2016) 7561-7565
Minko, Determination of the thermal conductivity of wood insulation materials in conditions of non-stationary heat transferInternational, Journal of Applied Engineering Research. 22 (2014) 15791
Zajcev, Effective Fine-Grained Concrete with High-Dispersed Additive Based on the Natural Mineral Wollastonite, FarEastСon - Materials and Construction: Materials International Scientific Conference «FarEastCon». 945 (2018) 85-90
Bondarenko, Effective Highly Dispersed Additive for Concretes on the Basis of Natural Mineral Raw Materials, FarEastСon - Materials and Construction: Materials International Scientific Conference «FarEastCon». 992 (2019) 168-172

Key Engineering Materials Vol. 814, (2019) 12-18
Walter, Advances in zirconia toughened alumina biomaterials for total joint replacement, Journal of the mechanical behavior of biomedical materials, 31 (2014) 107-116
Materials, 12(15) 2440
Niihara, A fracture mechanics analysis of indentation-induced Palmqvist crack in ceramics, Journal of materials science letters, 2 no.5 (1983) 221-223
Awaad, Toughening and strengthening of Nb2O5 doped zirconia/alumina (ZTA) composites, International Journal of Refractory Metals and Hard Materials, 48 (2015) 338-345

It is necessary to study the mechanical behavior of the materials especially under thermo-mechanical loading.
The fiber and coating are considered as linearly elastic materials.
The external loading that applies on the materials will be cyclic mechanical loading and cyclic temperature.
Materials Science & Engineering A. 1997, A229(1-2): 192-202
International Journal of Nonlinear Sciences and Numerical Simulation, 2010, 11(7):543-552 [7] H.M.Huang, X.L.Xu.

Introduction Nano-machining of brittle materials is possible, using the ductile mode in which material is removed by plastic extrusion.
To study the behaviour of the brittle-to-ductile transition of brittle materials, indentation was commonly used in machining field [1-6].
Nano indentation is an important technique for studying the mechanical behaviour of materials at nanometric scale.
It has been an important topic that cracks occurred on brittle materials' surfaces can be predicted [7-9].
Porto: Journal of Materials Science Letters Vol. 18 (1999), p. 1185

(2) The constitutive relation of metal materials can not be gotten at high speed processing, so the constitutive relation at low speed processing is used in this model
Acknowledgement This research is supported by national nature science foundation of China (NSFC) project (No: 50975229) and science & technology project of Shaanxi province, China (No: 2009JQ7003）.
CIRP Journal of Manufacturing Science and Technology, Vol. 1(1) (2008), p. 2 [2] H.
Journal of Plasticity Engineering, Vol. 15(2) (2008), p. 6 (In Chinese) [3] F.K.
Journal of Xi'an University of Technology, Vol. 25(4) (2009), p. 383 (In Chinese)

ACS Applied Bio Materials, 4(5), 3909–3936. https://doi.org/10.1021/acsabm.0c01335 [2] Ali, R., & Yashima, M. (2005).
Journal of Materials Chemistry C [9] Novianti, D.
Progress in Materials Science, 117, 100734
Journal of Environmental Sciences, 26(7): 1489-1495 [15] Yang, H., Liu, D., & Xue, X. (2012).
ACS Applied Materials & Interfaces, 6(15) [20] Zhuang, J., Tian, Q., Lin, S., Yang, W., Chen, L., & Liu, P. (2014).