Search results

Department of Innovation Engineering, University of Salento, Via per Monteroni, 73100 Lecce, Italy patrizia.bocchetta@unisalento.it Materials science Liang-Yu Chen Prof.
School of Materials Science and Engineering, Jiangsu University of Science and Technology, Mengxi Road 2#, Zhenjiang 212003, China lychen@just.edu.cn Materials science Juliana Dias Corpa Tardelli Prof.
Organization of the Text Materials.Section Headings.
Materials Science and Engineering: R: Reports 80(2014) 1-36
Clem: submitted to Journal of Materials Research (2003) [5] P.G.

However, it is difficult to ensure the machining accuracy because of the machining difficulties of materials and structures.
In the experiment, the milling way is down milling, test material is Ti6Al4V and the cutting fluid is used.
Acknowledgments The research is supported by National Natural Science Foundation of China (Grant No. 51405226), and Jiangsu Provincial Natural Science Foundation of China and National Science (Grant No.SBK2014043631)and Technology Major Project of the Ministry of Science and Technology of China (Grant No. 2014ZX04012014).
Yan, Cutting force prediction for circular end milling process, Chinese Journal of Aeronautics. 04 (2013) 1057-1063
Chen, FEM-based Prediction and Control of Milling Deformation for a Thin-wall Web of Ti-6Al-4V Alloy, Materials Science Forum. 800 (2014) 368-373

In some cases, more than one type of balls are used for grinding raw materials.
From a microstructural point of view, the two materials show significant differences.
Maldonado, Effect of titanium on the as-cast microstructure of a 16%chromium white iron, Materials Science and Engineering A 398 (2005) 297-308
Jena et al., Improvement of toughness of high chromium white cast iron: duplex ferritic-austenitic matrix, Materials Science and Technology 34 (2018) 299-304
LUdema, (Eds), Proc. of wear Materials, ASME, New York, 1983, 12-18

Within the elastic range of the materials, natural frequency of thin-walled components can be analyzed quantitatively with the software Abaqus.
Wen, An improved prediction of stability lobes using nonlinear thin wall dynamics, Journal of Materials Processing Technology (2010).
[2] Ge Maojie, Sun Jie, Li Jianfeng, Study on milling stability of thin-walled titanium alloy components with paraffin reinforcement, Journal of Shandong University(Engineering Science)(2011) vol.41,No.1(71-77)
Becker, Modeling and simulation environment for machining of low-rigidity components, Journal of Material Processing Technology (2004)vol. 153-154(67-73)
Journal of Material Processing Technology (2003)vol.139(332-336)

These observations suggested that the quantity and size of ablated materials depended on the pulse power and the confinement effects of the liquid.
The ablated materials appeared during the laser ablation need four stages to perform [4].
Dispersed materials can be nanoparticles, small clusters, free atoms and ions.
Kim: Journal of Colloid and Interface Science 311 (2007), p. 424
Yang: Progress in Materials Science 52 (2007), p. 698

Straser, New effective disaster forecasting methodology, MM Science Journal, 10 (2023) 6662-6667
Behun, Selection of materials hydroxylapatite using the method of analysis of hierarchy, MM Science Journal, 6 (2023) 6472-6477
Jablonský, The influence of hydrogen concentration in natural gas on heat flows in a thermal aggregate, MM Science Journal, 12 (2022) 6162-6168
Venkataramanan, Si3N4–TiN conductive ceramic composites: topography on EDMed surfaces and precise drilled holes, Materials science and technology, 39:15 (2023) 2006-2017
Gopal, Advanced Materials for Promoting Sustainability (2022) 6022550 [26] D.P.

This increased interest can be attributed to the fact that the optical and electrical properties of these materials are highly dependent on particle size, and that materials make this very simple due to superior particle size control [12].
Materials and Methods Figure. 1 depicts a diagram of laser ablation for nanoparticles in a liquid environment.
Synthesis, properties, and applications of carbon nanotubes filled with foreign materials: a review.
Materials Today Physics. 7 (2018) 7-34
Materials. 12(12), (2019) 1976

MATERIALS AND METHODS Material and reagent.
Journal of Colloid and Interface Science, 268(2): 330-340
Journal of the Science of Food and Agriculture, 86(12): 1826-1832
Journal of Applied Polymer Science, 100:1277-1281 [9] Gao Tianming. et al. (2010).
Journal of Applied Polymer Science, 109:1944-1949 [11] Zheng changren.

Using higher-order terms of the Williams expansion is necessary for assessment of fracture behavior of quasi-brittle materials.
Introduction and motivation Quasi-brittle materials exhibit their specific fracture behavior, which assessment is not described sufficiently yet.
Fatigue & Fracture of Engineering Materials & Structures 00 (2010) 1-18
Seitl, Accurate description of near-crack-tip fields for the estimation of inelastic zone extent in quasi-brittle materials, accepted to Key Engineering Materials (expected in 2013)
Keršner, Over-deterministic method convergence study on a mixed-mode geometry, under review in Applied Mechanics and Materials (expected in 2013)

Náhlík7,g Institute of Physics of Materials, AS CR, and Institute of Solid Mechanics, Mechatronics and Biomechanics, BUT Faculty of Mechanical Engineering; Brno, Czech Republic 2Institute of Physics of Materials, AS CR, Brno; Czech Republic 3Polymer Competence Center Leoben GmbH, Roseggerstrasse 12, 8700 Leoben, Austria 4Material Science and Testing of Polymers, Montanuniversitaet Leoben, Otto Gloeckel-Straße 2, 8700 Leoben, Austria 5,6Montanuniversität Leoben, Austria 7CEITEC IPM, Brno, Czech Republic aslavik@ipm.cz, bhutar@ipm.cz, cmichael.berer@pccl.at, danja.gosch@unileoben.ac.at, eflorianarbeiter@uniloeben.ac.at, fgerald.pinter@unileoben.ac.at, gnahlik@ipm.cz Keywords: fracture mechanics, failure of polymer bearings, mixed mode, numerical modelling Abstract.
Study of fatigue of roller bearing elements made of POM (Polyoxymethylene) and a general lack of knowledge about fatigue of materials in mixed modes caused a need to design a special specimen loaded under mixed mode conditions.
Schirmeisen: International Journal of Fatigue Vol. 62 (2014), p 93 [2] J.
Sih: Journal of Basic Engineering Vol. 85 (1963), p. 519 [9] M.R.
Aliha: International Journal of Solids and Structures Vol. 46 (2009), p. 311