Search results

MIMO antenna correlation measurements are very difficult to collect large amounts of data need to be complex and time-series data analysis.
Mutual coupling reduction in MIMO antenna system using EBG structures [C].

A series of speeds has been chosen to test the accuracy of the software by Dazheng Wang; It showed that the simulation method that FLOW-3D is employed to simulation the fluid field of the ship and predict resistance of it can replace part of the model test to save the costs, which has a good agreement between the simulation results and experiment data, especially the trends of resistance curves of the simulation results and experiment data, are basically consistent with each other [4].
At the design speed, the resistance of the TKS is significantly reduced and with a maximum reduction about 30% comparing with the RBS and 50% comparing with the SKS 2.

It is assumed that the size distribution of bubbles is described by lognormal density function with logarithmic standard deviation , which correlates well with the existing experimental data (e.g., [9]):
The results of simulations show that even minor amount of free gas causes sound speed reduction in a low frequency range and drastic non-monotonic changes at frequencies close to the resonance frequency of bubbles.
As it follows from the numerical data obtained, sound attenuation in a polydisperse mixture at different frequencies may be both less and more than in an equivalent monodisperse system.

Controllable loads due to its’ thermal inertia, such as refrigerators, freezers, electric water heater (EWH), can imply a substantial energy-storage potential, which allows for a temporary reduction or increase of consumption.
Fig.3 Block diagram frequency regulation for a single area with PEVs and controllable loads Simulation Results The data of system is identical and shown in Table1.
Table 1 Data of power system Parameter Value Parameter Value System Base (MW) 10 Nominal Frequency(Hz) 60 (sec) 0.2 ( MW/Hz) 1/5 (sec) 0.6 ( Hz/MW) 0.3 (sec) 8 (MW/Hz/sec) 2/15 (MW/Hz/sec) 5/3 30% In this paper, 200 PEVs and 100 EWHs are participated to the frequency regulation of the power system.

While third-order cumulant as follows, in which the random variable self- third-order cumulant is (8) Fourth-order mutual-cumulants of random variable, can be expressed as (9) The coefficients will be estimated according to collected data, and formula (9), and then the time delay can be estimated according to the maximum value of.
Experimental results and analysis 4096 length of zero mean non-Gaussian time series data and two zero-mean noise sequence of independent Gaussian are used in the experiment.
In addition, it shows that the bispectrum has the strongest noise reduction capability, and better filtered Gaussian noise, TDE based on cumulants also showed good filtering capacity, the correlation curve is good, the noise suppression ability is poor using correlation method.

Major mineral oxidation/reduction boundaries in sulphide deposits are very often heavily colonized by bacteria which can be a significant source of organic carbon, subject to volatilization as hydrocarbons [2].
Results and Discussion Table 1 shows the data of bacterial population and pH in each of the flasks after one month of starting the experiment, just before sealing the flasks and starting the flow of synthetic air.
Table 1: Experimental data on pH, bacterial population and metal recoveries.

The practical application in Jibei power grid indicates that this model can meet the compiling requirements of day-ahead generation schedule, realizes the prior acceptance of wind power and contributes to the energy saving and emissions reduction in power field under the power grid security constraint. 1.
According to the former analysis on historical data of wind power integration and operation control, it is found that the insufficient acceptance of wind power is due to the weak power grid structure as well as the irrational power layout, which cannot meet the requirements of powering reliability after the input of high-permeability wind power[5].
By taking a practical data construction case in a typical winter day, it checks and analyzes the constructed module.

The facilities offered by the research centers – database, software - led to rapid selection and configuration solutions, demonstrating achieving research productivity growth and a substantial reduction of times redesign.
The locating mode for inserts Radiating insert located on the inner cylindrical surface; tangential insert placed on the inner cylindrical surface, radiating insert located on the front surface, tangential insert placed on the front surface; Selecting Constructive Solutions The data resulting from the previous heuristic analysis represents a starting point for determining the morphological space, which in this case is compound of nine components (E, F, G ) each having between 2 and 4 configurations ( E1, E4, F1, F2, F3, F6, G1, G2, G4 ), a total of 24 combinations (2x4x3).
Databases contain both technical data specific to industrial design activity, knowledge base, but also specialists and customer base.

After cold storage at 4 o C for 24 h, presence of OS rice starch reduced retrogradation of rice starch mixtures as indicated by reduction of measured retrogradation parameters based on the three abovementioned rheological properties. 1.Introduction Modification of starch with octenyl succinic anhydride(OSA) was patented by Caldwell andWurzburg [2].
Data were statistically analyzed by an analysis of variance (ANOVA) test procedure and differences identified by Tukey's HSD test (p , 0.05) using SPSS 12.0 for Windows (SPSS Inc., IL, USA). 3 Results and Discussion 3.1 Degree of substitution DS of the octenyl succinate starch used in the experiment was 0.016. 3.2 Pasting property RVA pasting curves of the normal rice starch, octenylsuccinate starch and blends of native and OS starch are shown in Fig (not shown) and the RVA parameters are listed (Table not shown).
These experimental data fitted well with power law and Casson's model (r 2of 0.95-0.98 and 0.94-0.99,respectively).

In order to get a better handle on the effects of corrosion pillowing on the integrity of the lap joints, data regarding the chemical composition of the corrosion product of LY12CZ were used to develop a mathematical model for correlating the amplitude of the pillowing deformation of the outer skin of a lap joint toe the degree of corrosion within the joint.
The stresses resulting from the internal pressure, and the reduction in thickness caused by the material loss were well taken into account.
Fig.3 shows that the results of three-dimensional FE model are good agreement with the mathematical data and prove that the FE model in this paper is correct.
Mathemacal Data FE Data Fig.2 FE mesh and boundary conditions of panel Fig.3 Comparison of data from two models Parametric Studies of the Bolt Joint A simply lap joint configuration was chosen for this study and consisted two skins of equal thickness, 2mm, fabricated from LY12CZ.
(a) no corrosion (b)corrosion 1%(c)corrosion 6% Fig.8 Stress contours of lap joint for different corrosion level Conclusions Three-dimensional finite element model of bolted joint can produce results in close agreement with mathematical model data.