Search results

Target Function of DG Capacity Planning As shown in Fig. 1, DG is accessed to each load point.
So target function of DG capacity planning in distribution network is: (1) Among them, P0 represents distribution network active power consumption volume of the system S.
If the grid shown above is equivalent to radial distribution circuit, the results are shown in Fig.4, after equivalence, each load value is shown in Table 1, where 10 kV bus is the balance node.
References [1] Perdana A, Carlson O, Persson J.Dynamic response of grid一connected wind turbine with doubly fed induction generator during disturbances.
WIND ENERGY, 2006,9(4):479-95

The bandsaw milling process accounted on experiment has the following parameters: Table 1.
Figure 1.
References [1] GHOSH ET AL. (2007) Estimation of tool wear during CNC milling using neural network-based sensor fusion.
MechSyst Signal Process 21:466-479
IEEE Transactions on industrial electronics, vol. 34, no.1

Frictional behavior of glass fiber reinforced polyester under different loads Jan Quintelier1, a, Filip Van den Abeele1,b, Liesbet De Doncker2,c , Wim De Waele 1,d, Joris Degrieck1,e and Pieter Samyn1,f 1 Laboratory Soete, Ghent University, St.
In Fig. 1 an overview of the evolution of the coefficient of friction for different F*v values is given.
Fig. 1: Overview of the Coefficient of Friction at different FV values The circled values are tests performed at low loads.
If well looked at Fig. 1, the circled values, there is no difference between the different orientations.
Forum, Vol. 475-479 (2005), pp 1083-1086 [19] J.

Excel 1 shows the setting of various parameters.
Implementation steps as follows: Step 1 Collect the condition of equipment fault, analysis of causes of the failure, and form historical data set which is stored in HDFS.
References [1] J.H.
Neurocomputing, 2002, 48 (1): 85-105
Journal of statistical physics, 1988, 52(1-2): 479-487

Enhancing the outside interference of the buffer is a fundamental solution for the body of eutrophication[1].
Influence of Temperature on nitrogen nutrients It shows influence of temperature on concentration of NH4+-N in water body in Fig.1.
From the Fig.1, temperature increase and time prolongation will lead to a rise of NH4+-N in group B and group A.
Fig. 1.
Lan, “The Overview of aquatic invertebrates excretion of nitrogen,” Guangxi Science, vol. 15, no. 1, pp. 92-96, 2008 [7] Agnieszka Pinowska,et al, “Effects of snail grazing and nutrient release on growth of the macrophytes Ceratophyllum demersum and Elodea Canadensis and the filamentous green alga Cladophora sp,”Hydrobiologia, vol. 479, pp. 83-94, 2002 [8] X.

This is a universal problem facing mankind who must to deal with[1-2].
Results Tests results of compressive strength of garbage blocks of different curing ages were shown in Table 1.
(1) Where, i stand for the number of a certain level in a certain factor.
(1) The compressive strength of garbage blocks in each group all increased with its ages.
References [1] CHEN Xiaoan, DU Bo: Inner Mongolian Environmental Protection Vol. 21(2009),p.64-67, in Chinese

Introduction Cloud computing has emerged as a popular solution to provide cheap and easy access to externalized IT (Information Technology) resources [1].
The architecture of this system is designed based on a key principle that is the separation between data connection and control connection, as shown in Fig. 1.
Fig. 1 System architecture.
References [1] D.
Neely, “Dynamic Resource allocation and Power Management in Virtualized Data Centers,” Network Operations and Management Symposium (NOMS, 10), Apr.2010, pp.479-486.

The experimental device of ice disk polishing is shown in Fig.1.
The disk needs be pre-neatened before experiment and metal material should be pre-cooled because of its quick heat conduction [1].
During Journal Title and Volume Number (to be inserted by the publisher) 479 sliding friction, the surface rough peaks collide with each other at high speed.
References [1] W.N.
Liu: 4th International Symposium on Experiment and Measurement (Shanghai, China, June 1-3, 2001).

There were many works have been carried out in the recent years in the dynamic behavior of composites pipes and plates [1-6].
The volume fraction is found to be 0.6.The material properties were determined by using universal testing machine and tabulated in Table 1.
REFERENCES [1].
NA, Design Study of Multilayered Composite Spherical Pressure Vessels, Journal of Reinforced Plastic and Composites, VII,(1992). 479-493 [15].
Sayman, O, Analysis of Multi-Layered Composite Cylinders under Hygrothermal Loading, Composites Part A, 1-11. . (2005)

., intermediate density, thermal diffusivity) [1,2].
Fig. 1: (a) shape and dimensions for mould (b) sand mould and (c) permanent mould.
References [1] A.
Enginnering and Aplied Sciences, 5(1) (2010) 32-36
Alloys and Compounds. 463 (2008) 475-479