Search results

The samples were collected as Li et al. [8].
Staudt et al. [13] revealed large seasonal changes in both the quantity and composition of the monoterpene emissions from Pinus pinea.
Holzko et al. [22] suggested that a twofold intraspecific variation was important relative to long-term effects of light.
Vol. 52 (2006), p. 84-89 [15] E.L.
Vol. 6 (2006), p. 1267-1274 [17] E.L.

Nasr-El-Din.
[4] Liu, H., et al.
[5] Dai, C., et al.
[6] Feng, Y., et al.
[8] Cheng, J., et al.

McFadden, High strain rate superplasticity in a friction stir processed 7075 Al alloy, Scripta Mater. 42 (1999) 163-168
Ma, A.L.
Lee, Texture and weak grain size dependence in friction stir processed Mg–Al–Zn alloy55, Scripta Mater. 55(2006) 637-640
El-Rayes, E.A.
El-Danaf, The influence of multi-pass friction stir processing on the microstructural and mechanical properties of aluminum alloy 6082, J.

McKenna et al. [9] formulate this more precisely.
By calculating the integral of the quantities, the indicators compare energy amounts similar to the indicators that McKenna et al. defined.
Table 3: Technical specifications and used dimensions for the modelled regenerative supply system of the Green Factory Bavaria in Augsburg Technology Specifications Amount Final value CHPS Power: 8 kWth / 4 kWel Partial load factor: 0.5 1 Nominal el. power: 4 kWel Heat pump Power: 4 kWth Coefficient of Performance (COP): 4 1 Nominal el. demand: 1 kWel Wind turbine Power: 10 kW Degree of effectiveness: 30 % Hub height: 21 m Rotor diameter: 6.5 m 2 Nominal el. power: 20 kWel Photovoltaic system Area of one module: 1.643 m2 Degree of effectiveness: 16 % Angle of panels: 30 % 188 Covered area: 309 m2 Evaluation of the system.
Finally, the degree of autonomy by McKenna et al. reduced, since the storage system basically causes a smoothing of the residual load.
Table 5: Calculated indicators (Eq. 1-9) for the simulated year 2014 of the modelled energy system of the Green Factory Bavaria in Augsburg with two configurations of electrical storages (dimensions indicated in the heading of the columns) Indicator el. storage 30 kWh / 30 kW el. storage 180 kWh / 30 kW DSSMcKenna 0.7839 0.9053 SCRMcKenna 0.4573 0.5685 DAMcKenna 1.7142 1.5924 DAK&H 0.0697 0.3129 SCRK&H 0.0407 0.1965 DSCSchreiber 0.4573 0.5685 RSSSchreiber 0.7839 0.9053 DSS 0.4555 0.5876 Figure 5: Residual loads of the energy systems including electrical storages for the year 2014 for the modelled Green Factory Bavaria Augsburg sorted by size of power with a zoomed sector between the hours 1000 and 5000 Conclusion and outlook An analysis of the state of the art for the evaluation of energy self-sufficient systems showed a lack of an accurate indicator that considers contemporary power effects.

El-Alej et al. [15] monitor sand transport characteristics and showed a correlation between minimum transport condition and acoustic emission energy levels.
El-Alej et al. [16] demonstrated that acoustic emission technology is capable of detecting the presence sand particles in the two-phase flow.
[15] El-Alej, D.
[16] El-Alej, D.

[13] Marwa Adel and Azza El-Maghraby, Ossama El-Shazly and El-Wahidy F.
El-Wahidy, Ossama El-Shazly and El-Wahidy F.
El-Wahidy, Synthesis of few-layer graphene-like nanosheets from glucose: New facile approach for graphene-like nanosheets large-scale production, J.
[15] Karina Bustos-Ramírez1,2,3, Carlos Eduardo Barrera-Díaz1, Miguel De Icaza-Herrera3, Ana Laura Martínez-Hernández2,3,Reyna Natividad-Rangel1 and Carlos Velasco-Santos2,3*, Bustos-Ramírez et al. 4-chlorophenol removal from water using graphite and graphene oxides as photocatalysts ,Journal of Environmental Health Science & Engineering. 13:33 (2015) 1-10

Pre-aging and Maturing Effects on the Precipitation Hardening of an Al-Mg-Si Alloy T.
Hamamda a (a) Laboratory of Themodynamic and treatment of surface of Materials, Physics Institue Mentouri University, Road Ain -El Bey, Constantine, 25000, Algeria abidtah@yahoo.fr Keywords: Al-Mg-Si Alloy, DSC, Reaction kinetic, Activation energy, Precipitation hardening Abstract.
Experimental procedure The examined material is an Al-Mg-Si alloy with excess of silicon.
This effect has been already observed by Marioara et al. [10].
This result is in agreement with the work undertaken by Miao et al. [3].

Amorphous Phase Formation and Heat Treating Evolution in Mechanically Alloyed Al-Ti Powders P.
D (0.5) values of the different Al-Ti alloys milled for different times.
DSC of the different Al-Ti powders milled for 50 h.
Sherif El-Eskandarany, J.
Al-Dabbagh, R.

Determinations of Total phenolic content (TPC) The total phenolic contents of crude extracts were determined with Folin–Ciocalteu reagent, according to the method of Luo et al. [7].
ABTS assay The method, based on the ability of antioxidant molecules to quench the long-lived ABTS radical cation (ABTS•+), of Re et al [9] was modified.
Vol. 33 (2011), p. 63-72 [6] H Abd El- Baky.
El Baz.
El.

El-Hawary et al. (1997) [1] presented test results of 8 RC beams which the effect of fire exposure time and the concrete cover thickness on the behavior of RC beams subjected to fire in shear zone and cooled by water is investigated.
Shang shouping et al. (2009) [3] reported shear strength experiments of 8 simple beams which the fire resistance of the RC beams strengthened with U-type high performance ferrocement laminate layer or without is analyzed.
Shang shouping et al
El-Hawary, A.
El-Azim, and S.