Search results

Table 1.
Fig. 1.
(1)
References [1] L.
Svensson: On the Problems of Thermal Analysis of Solidification, Material Science and Engineering A, Vol.413-414, 2005, pp. 474 - 479

The hole mesh is composed of 547 479 nodes.
the wave power exceeds 20 kW m−1.
References [1] António F.de O.
Journal of Marine Science and Application, 15(1):41-49, 2016
Brazilian Journal of Oceanography, 58(1):53-70, 2010.

The spectra of the films as deposited at room temperature, Figure 3(a) exhibits a prominent peak at 470 cm-1; while the film as deposited at 200 °C, Figure 3(b) shows a broad peak at 479 cm-1, which correspond to the transverse-optical (TO) reststrahlen band features of wurtzite structure InN crystal.
The obtained E1(TO) values are slightly shifted from the reported values 476 cm-1 [19].
References [1] J.
B 76, 20(2007) 205319-1-205319-6
Phys. 113, 1(2013) 013502-1-013502-12.

α =d-1 ln(1/T) (1) The dependence of α on incident light energy is given by the expression as follows [21, 22].
The secondary phase such as TinO2n-1 was found in the samples after the multi-round annealing.
References [1] D.
Techn. 53 (2010) 475-479
Chen, Interaction of thiophene with stoichiometric and reduced rutile TiO2(1 1 0) surfaces: role of Ti3+ sites in desulfurization activity, J.

Fig. 1 shows a comparative scheme of PLP and MFCC computation.
A perfect Spearman correlation of +1 or −1 occurs when each of the variables is a perfect monotone function of the other.
References [1] J.
Acta Psychologica Sinica 1 (1981): 76-85
Ear and hearing 29.4 (2008): 479-491.

The optimal plots for the response variables is given in Fig. 1.
References [1] M.A.
Eng. 3(2-3), (2015) 1-5
Islam, Use of slag as coarse aggregate and its effect on mechanical properties of concrete, Proceedings of the 3rd International Conference on Advances in Civil Engineering, CUET, (2016) 475-479
Tech. 2(7), (2015) 1-6

The constituents of the material are shown in Table 1, and material properties after solid solution heat treatment are shown in Table 2.
Then springback values of the work-piece can be obtained as shown in Eq. 1, where R0 is pre-deformation radius, Rf is radius after springback, shown in Fig. 2
Similarly, the tensile strength, yield strength and Vickers hardness are 479.1MPa, 349.2MPa, 139.8HV respectively.
References [1] Holman M C.
Journal of Materials Processing Technology,(1991),28(1-2):211-219

A constant sliding speed of 1 ms-1 was used.
Fig.1.
Table 1.
Conclusions 1.
Forum 475- 479 (2005) 401-404 [6] L.

Fig.1.
Results and Discussion The characteristics of the CCNBD sandstone samples are listed in Table 1.
Table 1.
References [1] Erarslan, N. (2011).
Rock Mech Rock Eng 48(2015):463-479 [11] Solomon, C.J., Breckon, T.P. (2010). 

Suitable system conditions for desulfurization additives. (1) The reasonable sewage system design.
The amount of water in the flue gas of #1 and #2 absorption tower outlets is less than 50mg/m3.
Effect of long-term application of desulfurization additives on desulfurization system. (1) The absorption tower system.
References [1] Z.G.
Chen: Guangxi Electric Power, Vol. 1 (2007), p. 53.