Search results

Using the measured heat flow data, the specific heat capacity as a function of temperature was determined.
The obtained data clearly characterizes water vapor storage capacity of the studied plasters.
The MBV data are introduced in Table 5.
A similar comparison of ideal and practical data was done, e.g., in [8], where the authors referred on differences between the data calculated using steady state effusivity values and data measured in a dynamic experiment.
The thermal conductivity and thermal diffusivity data is given in Table 6.

Data recording process.
Data Pre-Processing Fig. 4.
Data pre-processing.
Data reduction also occurs, where information is reduced without losing essential details.
Python programming code is commonly used for data reduction.

Finally, the conclusion is sum up compared with the actual data.
The forces, i.e. the preloads, applied to the workpiece by the clamping device prior to welding are firstly measured, then the data is cleared and the variation in forces can be measured after the start of welding.
The simulation results show that properly releasing the clamping force at the location of the clamping device contributes to a certain amount of reduction in the deformation of the flankwall.

The XRD data collected from various have the Hg-1223 phase and the analysis showed that all samples correspond to the tetragonal structure.
To investigate the reduction of (c) parameter will conclude that, the replacement of the yttrium by the strontium leading to a change in the size of the crystal lattice as a result of a change in the radii in ions of the strontium and yttrium where the radius of ions Sr [r Sr + 2 (1.12 A0)] is smaller Figure 2. pattern of XRD for HgSr2-xYxCa2Cu3O8+δ with yttrium substitution Figure 3 shown the electrical resistivity vs temperature for x=0 (pure sample) HgBa2Ca2Cu3O8+δ compound, critical temperature is determined from the figure by reference [19, 20].
Analyzes of XRD data collected from different samples indicate that all samples are polycrystalline and correspond to the Mercury -1223 phase.

The test data and waveform showed that all kinds of electric actuator performance have reached international advanced level.
So minimizing the absolute angle of SRM per step, then through the reduction gear, the precision can be effectively improved.
Electric actuator operation is not only through the position signal to determine the rotor position and speed, but also by the SRM can be calculated number of steps to get more data.

Harmonic current will produce a voltage drop on the resistance in power transmission line to make the voltage waveform distortion happen; and the reduction of the harmonic current will shrink the distortion of voltage waveform.
LM3S1138 Microcontroller Data Sheet. 2007-2008, online at: http://www.luminary- micro.com.

Therefore, it is very important to develop the recycling technology of vehivle dismantling waste for the harmless, stability, reduction and resource utilization of vehivle dismantling waste.
The composition characteristics of vehicle dismantling wastes from artificial disintegration and mechanical shredder are studied in this paper, which can provide reliable data for a recycling utilization of vehicle dismantling waste.
The data is near to reports by Roy C et al[15] and Chaala A. et al[16].

Each surface was firstly scraped and wetted to increase the adherence of the mortar and prevent early water reduction in the mortar.
Crack pattern at peak load (γτmax) of (a) URE_2, (b) GRE_3, (c) NRE_2 and at ultimate load (γult) of (d) URE_2, (e) GRE_3 and (f) NRE_2 Since no recommendations for calculating the tangent shear modulus of the rammed earth (G) were found in literature, different linear regressions were performed in ranges of 10% of τmax increased of a 2% step, using data coming from the LVDTs.
It should be noted that it was not possible to find only one range τ/τmax common for all the cases where the shear modulus results reliable, likely due to recording data by the LVDTs.
Even though, it was not possible to define a range τ/τmax common to all the samples for assessing the shear modulus; likely due to recording data by the LVDTs.
Further diagonal compression tests will be performed to overcome difficulties related to recording data.

Since launched the TIROS-II in early 1960s, scholars had retrieve land surface temperature by using satellite RS data.
Digital numbers of Landsat data were converted to effective temperatures based on radiance value, and then the temperatures were compared to SST generated from NOAA data by using field data calibrated algorithm.
The results showed that effective SST generated from Landsat data has polynomial correlation with NOAA’s SST data, where the accuracy of Landsat B62 is better than B61 on detecting SST.
Data sources and preprocessing.
Mono-window Algorithm for Retrieving Land Surface Temperature from Landsat TM6 Data.

Each final data point is an average value that has been obtained based on a statistical sampling of four specimens.
The reduction in strength with present of rubber content might tend to deboned from matrix.