Search results

Friction stir welding and processing, Materials Science and Engineering: R: Reports. 50, 1–2 (2005) 1–78
Dynamic recrystallization in friction-stir welding of aluminium alloy 1100, Journal of materials science letters. 16 (1997) 1801-1803
The investigation of typical welding defects for 5456 aluminum alloy friction stir welds, Materials Science and Engineering A 433 (2006) 64–69
Kolubaev, Scale-dependent subsurface deformation of metallic materials in sliding, Tribology International. 43, 4 (2010) 695–699
Effect of heat generation due to plastic deformation on behavior of surface-layer material during sliding, Journal of Friction and Wear, 30, 5 (2009) 324-328

Influence of Poisson's ratio Zhang Hailian, et al.[7]developed a viscoelastic incremental finite element method applied to incompressible materials to study the effect of distribution of Poisson’s ratio on solid propellant grain’s structural analysis and studied random viscoelastic finite element of Poisson’s ratio.
Yang Yuecheng, et al. [8] used the finite element method to study the effect of Material Poisson’s ratio under internal pressure load on stress and strain of grain.
Reference [1] ZHONG Tongsheng, WEI Feng,and ZHI Youhai: submitted to Journal of Natural Science of Heilongjiang University (2006) [2] ZHAO Bohua: submitted to Journal of Beijing Institute of Technology (1994) [3] Sullivan R.
W.: submitted to Mechanics of Time-Dependent Materials (2006) [4] WEI Shifeng, BAO Futing: submitted to Journal of Solid Rocket Technology (2006) [5] Agbossou A.: submitted to Polym.
V.: submitted to International Journal for Numerical Methods in Engineering (2001) [7] ZHANG Hailian and ZHOU Jianping: submitted to Journal of Propulsion Technology (2001) [8] YANG Yuecheng, FU Xuejin and ZHANG Yongxin: submitted to Aerospace Shanghai (2004) [9] ZHI Shijun, SUN Bing and ZHANG Jianwei: submitted to Journal of Solid Rocket Technology (2011) [10] CHANG Wujun, JU Yutao and WANG Pengbo: submitted to Acta Armamentarii (2012)

Materials and Method Raw Materials.
Journal of Materials Science, Vol. 42 (2007) p. 2917-2933
Davidovits, Geopolymer: Inorganic polymeric new materials.: Journal of Thermal Analysis and Calorimetry, Vol. 37 (1991) p. 1633-1656
Advanced Materials Research (2013) Vol. 686, p.227-233
Advanced Materials Research (2011) Vol. 341-342, p. 189-193

Materials Science and Engineering A. 325(2002) 286~291
Archives Of Metallurgy And Materials. 61(2016) 1075~1081 [5] M.
Journal of Materials Science. 41(2006) 6228~6236
Journal of Materials Science. 20(1985) 1141~1149
Materials and Design. 33 (2012) 372~375

Gigacycle fatigue of different materials Gigacycle fatigue behavior of materials is not constant but varies from material to material.
Mechanics of materials.
SCIENCE CHINA Physics, Mechanics & Astronomy, 2013, 56(3): 617-623
Journal of material science 39 (2004) 687– 689
Materials Research, Vol. 8, No. 4, 443-446, 2005.

Figure 3: The comparison of predicting result of early bolting rate and 2011 two seasons’ measured data Table 3: Materials of 2012 two season planting stem mustard in early growth period and early bolting No.
The planting materials only include 2011 and 2012 that lead to the sample is very small and there are some limitations to our warning model.
The effect of temperature and light on development of tuber mustard [J], Zhejiang Journal of Agricultural Sciences, 1997, 9(1): 10-16
Journal of Glaciology and Geocryology, 2006, 28(1): 85-90
Journal of plant ecology, 1997, 21(1): 83-89

Hence, the effect of temperature and strain rate on the mechanical response of such thermoplastic composites are important when designing pipes using these materials [1, 2].
Materials and Method The tested injection mold composite was a 30 wt% of glass fiber/Polyamide 66 (PA6).
The material is suitable for injection molding and heat stabilized with improved hydrolysis resistance.
Govaert, Influence of fiber orientation, temperature and relative humidity on the long‐term performance of short glass fiber reinforced polyamide 6, Journal of Applied Polymer Science 138(19) (2021) 50382
Govaert, Prediction of plasticity-controlled failure in polyamide 6: Influence of temperature and relative humidity, Journal of Applied Polymer Science 135(11) (2018) 45942

The magnetic concentration bars were made from ferrite-based material with 60 mm in length as shown in Figure 6.
Hwang: Simulation of infrared rapid surface heating for injection molding, International Journal of Heat and Mass Transfer 49 (2006) 3846-3854
Chang: Dynamic mold surface temperature control using induction heating and its effects on the surface appearance of weld line, Journal of Applied Polymer Science 101 (2006) 1174-1180
Jung: Numerical analysis by new proposed coil design method in induction heating process for semi-solid forming and its experimental verification with globalization evaluation, Material Science and Engineering A 341 (2003) 121-138
Hwang: Development of barrel heating system in injection molding machine via induction heating, Rapid Prototyping Journal (Paper ready for production) (2014).

Approximately 30% fly ash is used for road conduction, building materials and agriculture.
It could be a nice adsorption material.
Materials and methods Materials Fly ash (Mei Zhou power plant) were dipped in HCl, and then washed thoroughly with demonized water to neutral and oven dried at 100℃ for 24h.
“Study on Zincic Wastewater Treatment by Modified Fly Ash”, Environmental Protection Science 2005,31(129):19-21 [3] Yu Xiaocai, Wang Ende, Wang Wuming “Environmental Treatment of Papermaking Wastewater by Modified Fly Ash”, Journal of Northeastern University (Natural Science) 2003,24(8)814-816
“Biosorption of chromium (VI) ion form aqueous solutions using walnut, hazelnut and almond shell ”, Journal of Hazardous Materials 2008.155(1-2):378-384

Introduction Three-dimensional (3D) braided composites reinforced by carbon fibers as a kind of advanced structure materials have been widely used in many industries due to the advantages over the conventional laminated composites, including light weight, high damage tolerance, ect.
Studies of its basic mechanical properties such as strength and stiffness are the most important precondition of how to put the materials into structure design.
References [1] LI Jialu, CHEN Li and JIAO Yanan: International Textile Science and Technology Forum(Academic Journal Electronic Publications,China2009)
Journal of Materials Engineering.
Journal of Materials Engineering.