Search results

(a) (b) (c) (d) fig.4 Micro-morphology of the coatings deposited in different KF concentrations (a)0g/L (b)5g/L (c)10g/L (d)15g/L As KF concentration increases, pores’ size increases but the number decreases. when the KF concentration is slow, the coating grows so slowly that molten oxides solidified inadequately. however, when it is high, the high temperature oxide solidified so rapidly that discharge channels are filled unevenly leading to many microcrack and coarse-grained structure.
Acknowledgements This research work is financially supported by the National Natural Science Foundation of China (Grant Number 51061006).

The increase in properties is usually associated to the structure and large numbers of grain boundaries4.

Introduction Silos are structures that have always concerned mankind due to their capacity to store bulk solid, such as grain, coal, cement and so on.
Only when the aspect ratio δ is very small numbers to nearly 0, the rupture plane can meet the top of the stored bulk materials.

They have implement application researches of it and has made some achievements in image enhancement, grain analysis, image compression and image fusion [4].
In case that it meets the condition, then (4) In case that it doesn’t meets the condition, then let , and return to step (b) (3) Calculate the residual volume: (5) In case that maximum values equals to or is more than 2 or the decomposed IMF number doesn’t meet the requirement, theshall be taken as new data and return to Step (2), letting

Pick up the one test point on the experimental plot, and the number of longitudinal samples were five with collected for each test point, and then depth of each sample is 20cm.
Characteristics of the enrichment coefficient and rules of arsenic, cadmium, lead of Rice, wheat grain [J].

Increasing of the wheel velocities decreasing grain size and introduces defects.
The increase of wheel velocities from 20 m/s to 40 m/s probably introduces a greater number of defects in the structure, producing a DSC curve with disturbances [8].

The acicular ferrite is also observed in A2 steel as well as ferrite and granular bainite, the metallographic figure of A2 COT steel shows that the ferrite and bainite grains are fine and uniform.
A2 fracture surface is large and deep equiaxed dimples at -20℃, and more evenly distributed and the number is greater, so the metal has good impact performance.

Simulation data source with data for the number of cycles from 0 to 255, VGA -RED/GREEN/BLUE-IN [7:0] of the data input terminal, matrix R / G / B-OUT [7:0] is converted by the matrix after the data, R / G / B - OUT data dynamically filtered [7].
Video gamut conversion process errors occur phenomena such as the image is not clear, the presence of the pseudo contour, grain noise and other phenomena, the dynamic filter can effectively be treated to reduce the error to eliminate the effects of noise.

Schematic diagrams of the casting process at (a) initial and (b) steady states Table 1 Casting parameters of the composite ingot Casting temperature [℃{TTP}8451 ] Casting speed [mm/min] Water flow rate [L/min] 3004 aluminun alloy695 4045 aluminun alloy:680 70 80 Table 2 Nominal composition of 3004 and 4045 alloys Elements Mn Mg Si Fe Al 3004 Wt% 4045 Wt% 1.5 0.05 1.2 0.05 0.3 10 0.7 0.8 Balanced Balanced To study the temperature field around the composite interface during the casting process, temperature in the interface and in the cooling plate was measured, measurement points in different positions are corresponded to thermal couples with different number.
It can be seen that in the 4045 alloy some needle-like primary silicon crystals (black part) are distributed at the boundaries of the coarse α-Al grains (white part); whereas in the 3004 alloy some manganese particles (black dots) are embedded in the α-Al matrix (white part).

This paper presents a structure evaluation method of the supporting plate of the steaming bucket, the evaluation indicator model is built based on fuzzy comprehensive evaluation theory, and the calculation of the structure evaluation is accomplished, so as to realize the better structure of the supporting plate, and maximize the scientific design of the plate correctly, which reduces fermented grains loss and production cost and to increase liquor distilling efficiency and liquor yield.
For example, evaluation matrix of hip range of motion is as follows: The same fuzzy evaluation matrix of the indicator layer and project layer can be obtained, finally can get all the fuzzy comprehensive evaluation matrix of project layer (is the layers of project number), such as the judgment matrix of the motion : D.