Search results

The reflectance data of ZnO, Ag-ZnO and Cu-ZnO nanoparticles are presented in terms of kubelka constant.
Impedance data (Table.2) are analysed in terms of Niquist plots which provide the ohmic and charge transfer resistances of the semiconductors.
Table 2 Binding constants (K) of benzimidazole derivative with ZnO, Ag-ZnO and Cu-ZnO nanoparticles Nanoparticles K n 100r2 ZnO 4.01 x 109 0.93 98.1 Ag-ZnO 3.89 x 108 0.99 99.6 Cu-ZnO 3.85 x 109 0.92 98.3 From the onset oxidation potential (Eox) and the onset reduction potential (Ered) of the derivative, HOMO and LUMO energy levels have been calculated [8] (Fig.4).The electron injection would be thermodynamically allowed from the excited singlet of the derivative to the conduction band of ZnO.

The contact angle (CA) of distilled water was measured at room temperature using an optical device OCA 15 Pro (Data Physics).
According to the data obtained the phosphating and anodizing methods significantly decreases the values of CA up to 2 ± 1°.
According to studies anodizing allows to obtain more resistant to moisture adhesive joints compared with chemical treatment: the maximum reduction in strength values was 25.3% and 39.3% of the initial strength, respectively.

After the reduction, the temperature was raised to 650℃ under flowing Ar atmosphere.
The data indicates that the top surface of AAO template with pore diameters 25nm has a strong catalytic property.
The above literatures and statistical data suggest that when an AAO template itself was used for CNT growth, a competitive catalytic carbon deposition between on the top surface of AAO template and in the pores was involved.

Methods firstly will come in PTS data vector into V a child of the overlap each vector Xv (its division usually has three ways: adjacent, random and intertwined), then each son the length of the vector into N/N.
The algorithm described the basic steps are as follows: the input data vector into V a child of the overlap each vector, notes for x (V); will V is vector to into M is vector, notes for b (M); subsidiary vector b (m) to end the search, and keep the other son vector unchanged until find make vector b (m) of the rotation of the smallest PAPR factor sequence; will M is vector b (M) to divided into L is vector, the first (3) step operation; So on until the results of the need.
An Over view o f Peak -to-average Pow er Ratio Reduction T echniques Formulticar r ierTr ansmission [ J] .

Introduction Reduction of overall vehicle mass, fuel consumption, CO2 emissions and consequently overall environmental impact has recently started to be one of the main priorities in automotive industry, following the recent environmental policy regulations being gradually adopted not only in the European Union but also worldwide.
In the first upper part of Table 1, values of shear modulus are, which were evaluated on the basis of data recorded by videoextensometer, are shown.
Shear modulus values of specimens G_1 and G_2, when axial strain was additionally recorded by strain gagues, were alternatively evaluated using these data.

From 1990s, non-continuous helical baffles have been studied increasingly in open-literature [9], but most of researchers were restricted to the computer simulation, that is “CFD” [10, 11], lack of the basis of the reliable experimental data.
Date reduction Parameters of shell side The shell-side is the shell-side fluid mean velocity, which is defined by (1) where is defined as the mean geometric value of and (2) (3) (4) Calculation of overall coefficient The overall heat transfer coefficient, is equal to (5) (6) (7) (8) (9) (10) (11) Correlations for Friction Factor and Nusselt Number (12) (13) (14) where hs is shell side heat transfer coefficient [5].
All experimental data are shown from Fig.3 to Fig.6.

Introduction March 14, 2006, the fourth meeting of the Tenth National People's Congress clearly stated: "Implementation of resource conservation and environmental protection as a basic national policy, building low-input, high output, low consumption, low emission, can be recycled and sustainable national economies and resource-saving and environment-friendly society in accordance with the reduction, reuse and recycle principle, in resource development, production consumption, waste generation and other aspects of consumption, the gradual establishment of the whole society resource recycling system, "the cycle of economic development mode.
Table 1 The correlation coefficients between main impact indicators and the amount of construction waste generated Construction area Income capita Construction Real Estate Real estate sales Population Beijing 0.988 0.853 0.828 0.670 0.959 0.776 0.915 Select the Beijing GDP (X1), real estate sales (X2), and construction area (X3) as the independent variable, construction waste Y is the dependent variable, the data shown in Table 2.
Table 2 Beijing construction waste generation and related indicators Year The amount of construction waste(10000t) GDP of Beijing(100 million Yuan) Real estate sales(10000 m2) Construction area(10000 m2) 1999 2400 2169.7 544.4 6556.5 2000 3000 2460.5 955.5 6995.9 2001 3300 2817.6 1205.0 8919.4 2002 3600 3130.0 1708.3 8617.6 2003 3100 3611.9 1895.8 11262.2 2004 3600 4283.3 2472.0 12363.6 2005 3600 6814.5 2803.2 14096.2 2006 3800 7720.3 2607.6 14096.2 2007 4000 9006.2 2176.6 14146.7 2008 3875 10062.4 1335.4 13871.2 2009 3917 11865.9 2362.3 14380.6 Note: Data from the 2000-2010 "Beijing Statistical Yearbook", "Beijing Construction Yearbook" and so on.

The function of measurement Unit is collecting voltage and current of system side and sending them to Data Processing Unit to calculate compensatory admittance that system needs.
A Feedback is added between SVC and Data Processing Unit in order to monitor the working position of SVC timely.
Loganathan: Power Quality Improvement of a Grid-Connected Wind Energy Conversion System with Harmonics Reduction Using FACTS Device, in IEEE International Conference on Advances in Engineering, Science and Management(ICAESM), pp.415-420, 2012.

Therefore, reduction of thermal energy losses has been always an actual theme.
According to the relevant literature sources, it is notable that less data exists about the basic heat insulating materials [10-13].
D., u.a., Thermal conductivity: X, Data for several pure oxides materials Corrected to zero porosity, J.

It is need more experimental data and the analyses to give the clear physical picture of perforation failure.
Finally the signals acquired by the sensors were amplified through YE5854 charge amplifier and then were transported into TDS420A data storage oscilloscope.
When the pipe was filled water and not pressurized, the perforation energy was 20-30% less than that of empty for thin pipe. 2) There was reduction in perforation energy with the increase in the pre-pressure of the pipe.