Search results

Thus nano-TiO2 in the hot rolling lubricant oil can also affect the wall energy, mechanical slip and thermal slip between the oil film and work roll under the contact area, and finally influence global lubrication.
Spikes, The effect of emulsifier concentration on the lubricating properties of oil-in-water emulsions, Tribol.
Yoshida, Influence of lubricant factors on coefficient of friction and clarification of lubrication mechanism in hot rolling, Tetsu To Hagane-J.
Wen, The tribological properties of oils added with diamond nano-particles, Tribol.
Xu, Effect of UV irradiation on mechanical properties and structure of poly(1,3,4-oxadiazole) fibers, Polym.

Blow molding evolved from the traditional blowing glass to plastic materials, as it can be engineered to provide bottles with a variety of dimensional and mechanical properties.
The idea of reheating a thermoplastic material, and then stretching it in order to enhance its properties, was first employed in extruded sheet in 1930s.
Although differences in mechanical properties of the two materials leads to different cutter material, the authors undertake the usage of the same cutters, in terms of dimensions, as well as the same toolpath strategies and similar machining parameter values for comparison reasons.
All these factors are affected by the design and mold material.
Moreover, their mechanical properties must be defined: maximum load, handling stability, barrier and stress cracking.

The openness of the network security problem The openness of the Internet and other factors led to the computer system under network environment many security problems.
(2) the use of security tools affected by human factors.
A security tool can achieve the desired effect, to a large extent depends on the user, including system administrators and ordinary users, improper setting can produce anxiety All factors.
(as shown in figure 4.1) rename administrator account "properties" dialog box, in this input new name of the administrator, as far as possible put it for ordinary users, and then built a more than ten super complex passwords, and enable the audit of the account, so even if the hacker to code and hard to kill.
Beijing: mechanical industry press, 2008.1:36 to 38 [8] photocopying.

The ohmic properties were evaluated by measurement of the I-V characteristics before and after annealing.
Electrical Properties I-V characteristics of the as-deposited and annealed contacts were measured to check for ohmic properties.
Structural Properties The effect of the Ti:Al ratio on the structural properties of the Au/Ti/Al ohmic contacts was investigated on the contacts having lowest resistivity.
Conclusions The results from the investigation on the electrical properties of nanolayered Au/Ti(70)/Al(30) and Au/Ti(30)/Al(70) ohmic contacts reveal that the different Ti:Al ratios do not affect the lowest resistivity value achieved.
In the case of the Au/Ti(70)/Al(30) contact this factor is the formation of ternary Ti3SiC2 compound, which is known to exhibit advantageous metallic properties.

It has been reported many times that quaternary AlCrSiN coatings promote a higher level of properties than typical TiAlN or CrAlN coatings [1,2,3].
Every type of coated cemented carbide turning insert was tested three times in order to exclude the impact of other factors involved in the process.
Cavaleiro, “High-temperature tribological properties of CrAlN, CrAlSiN and AlCrSiN coatings,” Surf.
Lee, “Effect of cathode arc current and bias voltage on the mechanical properties of CrAlSiN thin films,” Surf.
Mitterer, “Influence of Al and Si content on structure and mechanical properties of arc evaporated Al–Cr–Si–N thin films,” Thin Solid Films, vol. 534, pp. 403–409, May 2013

Material Properties All materials were considered as isotropic, homogenous, and linearly elastic (Table 1). 
Table 1 Mechanical properties of bone and implant materials [5-11] Component Material E (GPa) n Bridge framework Chrome/Cobalt 218 0.33 Implant Titanium 110 0.35 Bone Cortical bone 13.7 0.3 Spongy bone 1.5 0.3 4.
Element quality check was performed to avoid skewed elements that could affect the results.
The results of this study showed that biomimetics is one of the better solutions for prosthodontics success in dentistry: the optimization and reliability of dental cares have to take into account the mechanical properties of natural tissues and respect the physiology of the patient.
Wolf, Nonunion of the mandible: An analysis of contributing factors.

On the contrary, changing acid concentration of the electrolyte solution will not obviously affect burn defect result.
When sulfuric acid is increasing, the percentage of burn defect is almost not affected.
Experimental factors between of ramp time and sulfuric acid concentration was found that the ramp time 480s and sulfuric acid concentration 200 g/l can reduce the burning of aluminum in the best Hard anodizing process.
Muller: Mechanical Properties at Nanometric Scale of Alumina Layers Formed in Sulphuric Acid Anodizing under Burning Conditions, Ceramics International, Vol. 38 (2012), p.1627–1633.

Besides, there are some other influence factors such as artificial measurement error, statistical error and dynamic randomness, etc.
Taking advantage of the KFM or the EKF, a few scholars have been researching Back analysis of mechanical parameters [5-8] and deformation [9,10].
and are white noise sequences with the following statistical properties: , , (3) , , (4)
While, the initial values, and, affect filtering efficiency.
Additionally, initial value greatly affects convergence and computing speed, which implies an open issue in the future that how to choose an acceptable initial value in practical engineering.

It is noted that the resistance and behavior of a RC beam failing in shear under static loading significantly depends on many factors, such as the shape and size and the structural restraints of the RC beam, the loading condition, the amount of shear reinforcement, the shear span-to-depth ratio and the material characteristics[2].
Since the rapid loading machine can apply the load with the specified loading rate, the rapid loading machine is very suitable to investigate the influence of loading rate on the mechanical properties of RC beam specimens.
It was found that the test variables including the loading rate, shear span-to-depth ratio and shear reinforcement ratio clearly affect the load-midspan deflection relationships.
That for the RC beams failed in shear is affected by the dynamic compression and tension strengths of concrete.

Therefore, a new technique was researched and successfully applied to products that require a high accuracy and specific mechanical properties.
Packianather.., Investigation of micro-injection moulding: Factors affecting the replication quality, J.