Search results

Mithu, The influence of minimum quantity of lubrication (MQL) on cutting temperature, chip and dimensional accuracy in turning AISI-1040, Journal of Materials Processing Technology. 171 (2006) 93-99
Sreejith, Machining of 6061 aluminium alloy with MQL, dry and flooded lubricant conditions,Materials letters. 62 (2008) 276-278
Dhar, Effects of minimum quantity lubrication on turning AISI 9310 alloy steel using vegetable oil-based cutting fluid, Journal of materials processing Technology. 209 (2009) 5573-5583
Suzuki, The Assist Effect of Nitrogen Atmosphere on MQL Cutting Performance, Key Engineering Materials. 407 (2009) 321-324
Li, Effect Mechanism of Nitrogen Gas on Chip Formation in High Speed Cutting of Ti6Al4V Alloy Based on FEM Simulation, in Materials Science Forum.(2009)177-182

For brittle materials without joints, numerical studies have been implemented by a number of researchers using various numerical codes and models to simulate the processes of fracturing and fragmentation under blasting [7-20].
Zhu: Advanced Materials Research Vol. 230-232 (2011), p. 251-255
Zhu: Advanced Materials Research Vol. 230-232 (2011), p. 278-282
Zhu: Advanced Materials Research Vol. 225-226 (2011), p. 933-936
Journal of Sichuan University, Vol. 43 (2011), p. 1-8 (in Chinese)

In research of converting materials, people have paid more attention to monocrystal and body material of glass [13].
The individual materials were mixed with the mass radio K2B4O7: CaCl2·2H2O: Sm2O3 =65:7.5:2 in 450mL deionized water, heated at 35℃ for 3 h.
K2B4O7, CaCl2·2H2O and Sm2O3 were raw materials, the mass radio was K2B4O7: CaCl2·2H2O: Sm2O3 =65:7.5:2.
Journal of Sichuan University (Natural of Science Edition) .Vol.6 (2008), p.1441
[13] Du HY, Yang ZP, Sun JY.New Chemical Materials .Vol.37 (2009), p.5

Introduction With the constant progress of science and technology, engineering materials also got rapid development.
Engineering ceramics with high hardness, good wear resistance and chemical resistance performance advantages, such as new materials become an increasingly common.
In the menu manager, select【 display cut material 】, observation tool cutting trajectory.
If satisfied with the tool path, then choose confirm cutting material.
References [1] Yang M Y，in: Development of a composite suitable for rapid prototype maching, edtied by Hou Yongtao, Journal of Materials Processing Technology,BJ(2001),in press

Fatigue failure of cold forging tooling: causes and possible solution through fatigue analysis, Journal of Materials Processing Technology, 46 (1994) pp. 57–71
Geiger, “Estimation of tool life in bulk metal forming based on different failure concepts”, Journal of Materials Processing Technology, 80–81 (1998) pp. 602–607
Chen, “Fatigue life of cold-forging dies with various values of hardness”, Journal of Materials Processing Technology, 113 (2001) pp. 539–543
Lee, “High-cycle fatigue life prediction of cold forging tools based on work-piece material property”, Journal of Materials Processing Technology, 191 (2007) pp. 178–181
Lee, “Tool life prediction for the bolt forming process based on high cycle fatigue and wear”, Journal of Materials Processing Technology, 201 (2008) pp. 348–353

Mechanics behavior and deflection of the monolithic roadbed, deflection and compressive stress of earth subgrade evaluated in detail with respect to varied structure layer combination and materials parameters.
In the AASHTO design guide, based on different materials at the base layer, the recommended coefficient of friction between concrete and base layer could be shown in Tab.3.
Acknowledgement This research was supported by China Postdoctoral Science Foundation General Program (2011M500804), supported by China Postdoctoral Science Foundation Key Program (2012T50428) and supported by Key Laboratory of Road and Traffic Engineering of the Ministry of Education open fund (K201202).
International Journal of Solids and Structures, 1965( Vol.1):, 451-461
Journal Transportation Research Record. 2002(1809): 66-73

In this study, tomato plants are applied as experimental materials, using barrel simulation method, to probe the effects of root zone aeration on the leaves, root system growth and biomass accumulation of tomato seedlings.
Materials and methods Test material and experiment site.
Chinese Journal of Eco-Agriculture, 2004,12(3):65~67 (in Chinese)
Chinese Journal of Applied Ecology. 2008, 19( 3): 583~587 (in Chinese) [6] Yiling Liu，Zhouping Sun，Tianlai Li.
Chinese Journal of Applied Ecology. 2013，24( 3):741~746 (in Chinese) [8] J Guo S R, Tachibana S.

Journal of Microelectromechanical Systems, vol. 17, p. 20, 2008
Epitaxial Growth and Characterization of Self-Doping Si1-xGex/Si Multi-Quantum Well Materials [J].
Journal of Microelectromechanical Systems, vol. 23, pp. 213 - 219, 2014
Journal of Micromechanics and Microengineering, 2013, 23(12): 125021
Solar Energy Materials and Solar Cells, 2002, 72(1): 231-246.

China 2College of Chemistry, State Key Laboratory of Supramolecular Structure and Materials, Jilin University, Changchun 130012, P.R.
ZR2010BL025), Open Project of State Key Laboratory of Supramolecular Structure and Materials (No. sklssm201323)(Jilin University), State Key Laboratory of Inorganic Synthesis and Preparative Chemistry (No. 2011-13)(Jilin University).
Fan: Journal of Qinghai medical college, Vol. 32 (2011) No.1, p.53
Lu: Journal of Hebei Agricultural Science, Vol. 12 (2008) No.1, p.169
Guo, et al.: Li Shizhen medicine and material medical research , Vol. 20 (2009) No.9, p.2178

The FAO/S8010 silica particles slurry (Tianjin Jingling Electronic Materials Technology Co., Ltd.) with density of 1.1g/cm3, concentration of 35wt%, mean diameter of 30~40 nm and pH 11.0~12.0, was used as basic polishing slurry.
Xu and et al: Chinese Journal of Mechanical Engineering Vol.19(20) (2008), pp:2407-2411
Lu: Science and Technology of Particle Dispersion, Chemical Industry Press, China 2005
Liu and et al: The Chinese Journal of Process Engineering, Vol.4 (6) (2004), pp: 513-518
Yuan and et al: Chemical Journal of Chinese Universities, Vol.26 (11) (2005), pp:1998-2001.