Search results

The result indicated that for moisture sensitive adhesives, the strength reduction of single-lap joints with changes in both Tg and the conditioning temperature are related [6].
Both mechanical properties of Young’s modulus and Poisson’s ratio of adhesive of bulk specimen and adherent, stainless steel were keyed in engineering data.
The analysis data of T-joint specimen has failure stress in the range of 5MPa to 20MPa which is higher than the failure stress T-joint application in Fig. 4 (a).

John Craig and Poonekar[1,2] recommends that the development of a prosthesis can refer to the local potential, the issue of the environment, go green, back to nature and reduction of hazardous waste.
Materials socket prosthesis which will be discussed in this study are composite materials, especially natural fiber composites begins with the gathering of data that support the use of composite materials in the design of the product.
The data fibers and treatment are carried out as shown in Table 1.

Based on these data,the component characteristics and the preset control strategy,the vehicle controller generates control commands and sends the commands to the corresponding component controllers.The component controllers control the corresponding components to carry out the commands coming from the vehicle controller.
The results are consistent with the efficiency data in Figure 7, whereby the Fuzzy Logic Control Strategy easily surpasses the common Control Strategy.
Venayagamoorthy, “Plug-in vehicles and renewable energy sources for cost and emission reductions,” IEEE Trans.

Furthermore, the data show a sharp increase of the fracture toughness in the regime of slow crack propagation velocities.
Procedures for determining equivalent properties for propagating cracks are only used in research oriented work, and, as a consequence, only limited data are available in the literature [1, 2, 3].
The paper reports on data obtained by the one or the other of the techniques for achieving high crack propagaton velocities.
Typical data for these three types of tests are given in Fig. 5.
An evaluation of these data on the basis as described before yields the following results.

Methods: This software used the 6 dental prosthetic materials and color data from 4 shade guide system which were most frequently-used in clinic currently as basic database, to program 5 functional blocks including respectively CCS/CCM system; Dental Material Chromatic Value System; Vita Information System; Transformation of Colorimeter System; and Chromatic Value Difference Analysis.
In recent years, the lack data of ceramic and Zirconia ceramic which are extensively used in clinical led to the reduction of clinical applicability.
This test with manufacturers to provide repair materials, strictly in accordance with the manufacturer's requirements of sintering production-grade color, its color can more accurately represent the chroma value labels of dental materials, medical and research use, this program is not only to provide a convenient mode of the query, can also provide data for computer color selection information.
Through query this software, oral repair section doctors, and technician, and related research personnel, can informed 4 species different chords than color plate of chroma value distribution, turn can understanding master than color plate in color space of chroma distribution law and the the parts of chromatic aberration value, and can pursuant to reality more reasonable of application, produced more ideal of repair body, also can for computer selected color provides data reference.
Therefore, this method can convert any color measurement instrument, the measured color swatches of material data collection and enter the software, then this instrument for matching colors, you can get more accurate results, with high repeatability.

Temperature and displacement data were collected and compared with the prediction of the finite element model.
Temperature and displacement data are recorded to characterise the SMAHC behaviour.
The geometrical and mechanical characteristics of the composite material and SMA wires were used as input data for the simulation.
The simulation results are reported in Fig. 6, along with the recorded experimental data.
The LVDT and a second K type thermocouple attached to one of the SMA wires were connected to an acquisition system, displacement and temperature data were recorded using Labview.

(2) Grid measured data 1) 66kV power quality test data 66kV power quality indicators are shown in Table 1.
Fig.1 66kV busbar phase voltage curve 66kV busbar phase voltage curves of short-time flicker 66kV voltage busbars short flicker Figure 2 Fig.2 66kV busbar phase voltage curves of short-time flicker By analyzing the test data, Lishizhai 66kV substation busbar power quality in line is compliance with national standards.
The maximum load of the steel for a change, steel two variables, steel three variables and steel four variables total 180MW (​​also open furnace ,oxidation period), It does not consume power in each of the smelting reduction period.
By measured datas of the 66kV grid system show that the existing fixed stations compensating device does not solve the problem.
Depending on the operating data, normal operation of the system, the bus voltage changes as follows: 220 kV Bus: Maximum: 231 kV; Minimum: 226.4 kV; 66 kV bus: Maximum: 70.5kV; Min: 65.9 kV

Introduction The achievements of ICA in the separation of speech signals, biomedical signal processing, financial data analysis, image denoising and the application of face recognition, are described in the literatur [2]-[4].
ICA of Mixed Vibration Signal For the array signals, the number of Signals are often more than the number of array elements.Therefore, the first thing is dimension reduction with the process of signal whitening.

According to the equal circuit of solar battery to establish simulation model, then collecting data of adjusting the size of the load resistance, When the Light changing, Fig. 2 is the curve of solar battery’s characteristic.
On the Constant temperature from the curve we know the Open circuit voltage with light from the reduction of decline, on the contrary the Short-circuit current and Maximum output power rise.

In view of the fact that most extensions are built on top of objects which are in use during the construction process the speed of construction process and reduction of negative impact upon the users of the building are fundamental requirement.
According to data from Passive House Center three quarters of passive and low-energy houses built in Czech are built as wooden houses.