Search results

Then the conformity of model to an object is checked (verification), and modeling data are transferred to its real properties.
The composition of the resulted hypogene and hypergene minerals of the considered ore bodies, used in the modeling, is based on the published data [4].
The modeling data obtained show that the decrease of calcite amount and the increase of the silicate component in the models result in the increase of the oxidation- reduction potential Eh from 0.6 to 0.8 and decrease of the level of acidity-alkalinity pH from 9.6 to 6.18.
Data for models of oxidation of sulfides and host rocks at the KCM tailing dump with decrease of calcite content and increase of silicate component amount.
Verification of the modeling results by the literature data [1, 2] confirmed their reliability.

Summary of data recorded Stage Temp.
Chronically data of Enthalpy [kJ/kg] Sensible heat did not return to its baseline value until stage-D yet, latent heat started to come down to its initial value fairly quickly at the beginning of stage-C and then remained stable.
That is also the factor which leads to a reduction of relative humidity.
However, if the data was compared and analyzed to that showed in the diagram of absolute humidity (Fig.4), it can be found that the content of indoor water vapor was constantly on the rise after the heater was turned on; a 30% increase was noted in the first 5 minutes when the heater was on than that in 60 minute time.
Measured data in studied studio.

In order to reserve the maximum resemblance between noise data and model data.
We can observe the transformation between the clean and noise data from the both figures.
Table1 Average recognition results in different SNR conditions Data SNR Optimization DRA DRA only Corr Acc Corr Acc known data for recognition 20 dB 79.13 76.68 77.80 75.82 15 dB 67.83 64.44 61.10 58.40 10 dB 49.62 45.96 39.23 36.98 unknown data for recognition 20 dB 73.52 71.23 72.46 70.23 15 dB 62.92 60.01 58.18 55.95 10 dB 47.75 44.69 37.06 35.19 Conclusion The proposed method, compared with other solutions, properly enhanced the recognition rate in the high noise environment.
W, Eds., Advanced Digital Signal Processing and Noise Reduction, Second Edition.

Empirical data suggests material properties depend to a great extent on the rolling technology.
This data will expand the knowledge of the topic.
Source data Material: 08пс steel (US 1008, EU 1.1121).
The reduction in hardness towards the middle was observed in tensile-strained specimens as well.
For practical of the data presented herein in the engineering designs, refer to G.D.

Under the pressure of energy conservation and emissions reduction, reusing the pressure energy has become one important issue and takes great attention of the scientists.
Examples This example from paper by Chen Hui[5], fluids data are shown in Table 1.
Table 2 shows the specific match data between high-pressure fluids and the required-pressure fluids.
Table 2 Specific match data between high-pressure and required-pressure LP Matching data HP LP(1) LP(2) LP(3) LP(4) HP(1) 0.0000 1.0000 0.0000 0.0000 HP(2) 0.0000 0.0000 0.0000 1.0000 From Table 2, it can be seen that the specific matching is that: HP(1) and HP(2) are matched with LP(2) and LP(4), respectively, while LP(1) and LP(3) are unmatched.
The data for matching is shown in Table 3.

Actions Data1(s) Data 2(s) Data 3(s) Data 4(s) Ave.
It can be found in Table3 that, with the modified stitching device, Procedure 4 is reduced to 64.1S, that is 35% reduction.
Actions Data1(s) Data 2(s) Data 3(s) Data 4(s) Ave.

Media in Ad hoc networks are shared by multiple mobile stations which launch data transmission by way of random contention, and the hidden terminal problem can lead to confusion of the received signals, so that mobile stations cannot communicate properly.
This appearance will inevitably lead to unnecessary calls of congestion control and avoidance mechanisms, and thus cause a drop in TCP throughput and an increase in data transmission delay [7].
Table 1 Parameters of network simulation Parameter Numerical value Simulation time 600s Number of mobile nodes 50 Number of fixed nodes 250m Size of TCP data block 1460bytes Maximum transmission speed 0, 4, 8, 12, 16, and 20 m/s Communication service FTP Packet loss rate refers to the ratio of total number of discarded packets and total number of packets which the sending node sends after the sending node starts to send packets.
Throughput is defined as the average bit number of received data in network within per unit of time, which reflects network's ability to process data.
The greater throughput is, and the stronger network’s ability to process data is.

However, this paper assumes that Embodied Energy consumption in the use and disposal process is not included for the simplification and availability of data, and then Embodied GHG emissions aren’t included too. section headings are in boldface capital and lowercase letters.
Methodology, Procedures and Data Methods.
Procedures and data.
But the energy consumption in the use and disposal process is not included for the simplification and availability of data.
However, it is impossible to get the data, so this paper just use carbon emissions factors p=0.67released by Energy Research institute of the National Development and Reform Commission.

Table 1 below summarized the data obtained from Porous and Surface Analyzer.
For pure [hmim][Tf2N], the KH was 35.4±3.3 bar which was nearly identical with the published data [5].
This experimental data proved that the solubility of CO2 in solid supported ionic liquid was higher compared to non-supported ionic liquid.
This statement is supported with the experimental data from several researches [2-3],[5,6].
From the experimental data, it proved that solid supported ionic liquid can increase the solubility capacity of CO2 into ionic liquid by providing high surface area for intimate contact between CO2 and ionic liquid.

Since the subject was constructed based on previous building in 2007, the data in the construction stage are difficult to search.
According to the data in Shenyang Statistical Yearbook 2011, each urban household in Shenyang consumed 1473.7kwh electricity and 123.67m3 gas on average in 2011.
Based on the above data, we conclude P3=7951.51×103㎏CO2.
These results are derived from rough estimate of CO2 emissions of the buildings in the case, and basic data in the calculation come from the relevant literatures home and abroad.
As the purpose of this study is to understand the total emission of CO2 in the urban residential area in the total life cycle and the composition of emissions at different stages from the macroscopic perspective, it can believed that the above basic data basically meet the requirements of this study.