Search results

The group of resistor value selected for crowbar is {5, 2, 1, 0.75, 0.5, 0.2, 0.1} and {5, 2, 1.5, 1, 0.75, 0.5} for chopper .
The normal value of DC-link voltage is 1.18kV.
Calgary, Canada, 2009:1-9 [6] Xueqin Zheng, Donghui Guo.
IEEE Transactions on Energy conversion, 2007, 22(1):174-180
Wind Energy 2006, 9:479-495.

The internal structures in a non-central position or non-circular section of steel parts can be obtained through conversion by means of equivalent diameter, and for the relevant concepts, see the literature [1] in detail.
For different positions of the steel bar with the same diameter or noncircular cross-section steel parts, its structure analysis during cooling can be determined through equivalent diameter, detailed concept and specific matrixing methods are shown in above-mentioned tests.[1,2] Establishment of the Dynamic Phase Diagram The left chart in Fig. 1 is the new-type continuous air-cooling transformation curves of 25 carbon steel.[1] Taking the air-cooling of the carbon steel bar with a diameter of φ20 mm as an example, it can be seen from the chart that when the temperature is up to 700 oC, the ferrite (α) begins to be separated out from the overcooled austenite (γ); when the temperature is about 600 oC, α will finish the transformation; after air-cooling of carbon steel bar with a diameter ofφ20 mm, its core will be finally composed of P and α structures.
Fig 1.
Broken curves or lines in the diagram are the Take Fig.1 as an example.
Reference [1] Z Qing-Hua, C Hong, C Xiao-Dao, New-Type Dynamical Phase Diagrams and a Nonequilibrium-Lever Rule for Carbon Steels[J].The Physics of Metals and Metallography, 100 (5) (2005)472-479

Conductor parameters are listed in the Table 1.
Some results of KPT calculations are shown in Fig. 1.
Table. 1.
a b c d Fig. 1.
Lee, Strain Change and Creep Behavior of STACIR/AW Power Line with Heat Exposure, Materials Science Forum 475-479, (2005), 1751-1754 [7] Standard IEC 61597:1995 Overhead electrical conductors - Calculation methods for stranded bare conductors [8] B.

(a) (b) 66.19° 23.16° A(3 1 1) B(3 2 0) C(0 1 1) [2 3 3] Fig. 3 (a)TEM micrograph (Red marks indicate nano-SiCp); (b) Electron diffraction pattern of SiCp Fig. 3 shows TEM micrograph and electron diffraction pattern of nano-SiCp.
These parameters can match the d(3 1 1), d(3 2 0), d(0 1`1), θ(3 1 1)//(3 2 0) and θ(3 2 0)// (0 1`1) in the β-SiC crystal system.
Conclusions 1) The addition of nano-SiCp has a great influence on the primary α-Al crystals in nano-SiCp/A356 composites.
References [1] S.
Ultrasonics Sonochem. 40(2018) 472-479

The latter is usually defined by an Arrhenius law, accounting for the diffusional nature of growth: g=g0exp-QRT (1’) where g0 and the activation energy, Q (respectively 2.48.10-5 m2s-1 and 174 kJ/mol for Ni [8]), are material properties.
Table 1: List and values of the parameters associated to uncertainties.
Additionally, it must be noted that most of the uncertainties mentioned in Table 1 can be considered quite small compared to actual levels.
References [1] J.
Bellini, Properties, processability and weldability of a novel affordable creep resistant nickel base superalloy, Materials Science and Technology 24(4) (2008) 479-487

Fig.1 showed a binding curve obtained for paeonol-BSA.
The solid line (in Fig.1) represented the estimated curve by non-linear regression of the data.
The calculated content of paeonol in liuweidihuang pill and the RSD were shown in Table 1.
Table 1 showed that the values were satisfactory.
J. of Pharmaceutical and Biomedical Analysis, 2003, 32, 479-485

The ratio between cement and sand consumption was constant: C:S = 1:1.
The fiber content in the dispersed reinforced concrete was 1% of the cement stone volume.
X-ray diffraction patterns of foam concrete Table 1.
References [1] V.P.
Gugliandolo, Compressive and flexural strength of fiber-reinforced aerated concrete: effect of fiber content, curing conditions and dry density, Construction and Building Materials. 198 (2019) 479–493

Fig.1 Steering and suspension assembly developed by the Arab Academy Motors team.
The values of the applied loads are presented in Table 1.
Table 1 Loads applied on the upright as shown in Fig.3.
References [1] V.H.
Lee, "Structural optimization of a flapping wing micro air vehicle," in 2016 7th International Conference on Mechanical and Aerospace Engineering (ICMAE), 18-20 July 2016, pp. 476-479, doi: 10.1109/ICMAE.2016.7549587

Table 1.
References [1] Y.
Int J Photoenergy. 2011 (2011) 1-11
Nano Lett. 12 (2011) 479-485
UBU. 1(1) (2010) 1-8

Therefore, it has been widely used for manufacturing lathe bed and sliding guide rail [1].
Table 1 L25(55) orthogonal array and experimental results Exp.
The effects of grinding parameters on surface bearing index Sbi are shown in Fig. 1(a).
References [1] D.B.
Manu. 45 (2005) 467-479