Search results

Andrews, Characterisaton of residual stresses in machined surfaces of a high strength nickel-base superalloy Materials Science Forum 524-525 (2006) 587-592
Li, Residual stresses in face finish turning of high strength nickel-based superalloy Journal of Materials Processing Technology 209 (2009) 4896-4902
Part 2: microhardness variations and residual stress Journal of Manufactureing Science and Engineering 122 (2000) 632-641
Ridgeway, An analysis of the residual stresses generated in Inconel 718 when turning Journal of Materials Processing Technology 173 (2006) 359-367
Residual Stress Characterization Metallurgical and Materials Transactions 33A (2002) 3227-3234

After 7 days, the output materials of food waste degradation would be used in the cultivation of vegetables as organic fertilizer.
For farmers living around, the output materials were helpful, as they could be used in the cultivation of vegetables as organic fertilizer.
Applied Mechanics and Materials Vol. 109(2012), p. 65-69, in Chinese
Journal of Beijing Technology and Business University( Natural Science Edition) Vol. 29(2011), p. 69-72, in Chinese
Journal of Beijing Technology and Business University( Natural Science Edition) Vol. 28(2010), p. 40-44, in Chinese.

Leed: Materials Vol. 92 (2012), p. 263 [2] Y.
Han: Science Vol. 20(2008), p.1035 [6] R.P.
Han: Journal of Hazardous Materials Vol. 137(2006), p.550 [7] X.L.
Ho: Journal of Hazardous Materials Vol. 136(2006), p.681 [9] S.D.
Singh: Journal of Hazardous Materials Vol. 167(2009), p.1089 [10] A.

Experimantal Materials.
The Chinese Journal of Nonferrous Metals,2005, 15(5): 817- 822.
(In Chinese) [3] Hu Juan,Deng Jiangang,He Shuiyang, et al.Materials Science and Engineering,2001,19(4):71-74.
Materials Protection,2002,35（11）:6-8.
Chemical Materials for Construction,2004,3:8-11.

The attractive factors for the extensive use of the composite materials are that the composites exhibit high strength, low density, and excellent corrosion and fatigue resistance than its competing metallic materials such as aluminium, steel etc.
Glass fibre reinforced polymeric (GFRP) composites have been important composite materials and are used in fairings, storage room doors, landing gear doors, and passenger compartments in aircrafts [2].
The impact force based parameters were shown to only predict the initiation or onset of damage in various target materials [6, 7] but not the extent of the damage.
Soutis: Progress in Aerospace Sciences, 2005, Vol. 41(2), p. 143–151
Martin, Composite Materials: Fatigue and Fracture 5, Vol. 15, ASTM, Atlanta (1995), p 333-350

Further,the finite element analyses which relate the natural frequency and the sensitivity to geometric and material parameters are provided.
Journal of Beijing University of Aeronautics and Astronautics. 2006, 32(11): 1369-1372.
Chinese Journal of Scientific Instrument. 2006, 27(1): 42-44.
Laser Journal. 2005, 26(1): 26-27
Journal of University of Science and Technology Beijing. 2006, 28(1): 75-77.

Because of natural aging after solution treating these materials are not storable at room temperature in T4 temper.
Lopes: Journal of Materials Processing Technology, Vol. 92–93 (1999), p. 54–59
Ural: Journal of Materials Science Letters, Vol. 13 (1994), p. 383–385
Jezierska: Materials and Corrosion, Vol. 55 (2004), p. 77–87
Lendvai: Journal of Mat.

Introduction It is well known that ceramics materials have many excellent mechanical properties, such as high strength, high hardness, high melting point, and high stability, etc.
Table 1 Composition of the test material Ti3AlC2 Materials Grain size (µm) chemical composition (wt%) Ti Fe Si C Cl- Ti-powder ≤45 ≥99.2 ≤0.03 ≤0.01 ≤0.035 ≤0.04 Active Al Fe Si Cu N Al-powder ≤45 ≥99 ≤0.6 ≤0.3 ≤0.05 ≤0.01 C water ash volatile S C-powder 1 ≥96 ≤1.0 ≤0.3 ≤2.0 ≤0.4 Specimen is 3 × 4 × 36mm3 for bending test and the σb is calculated according to equation (1): wh2 LP3 2 f b =σ
The testing Ti3AlC2 ceramics has much better plastic behavior and fracture-resistance properties than most of the other ceramics materials.
Zhou: Journal of Materials Chemistry, Vol. 12 (2002), P. 455 [5] C.
Ai, et al: Journal of the American Ceramic Soc, Vol. 88 (2005), p.270

Wang: Materials Science and Engineering, Vols.
Schajer: Transactions of ASME, Journal of Engineering Materials and Technology, Vol. 110, (1988) p. 338 [8] G.S.
Schajer: Transactions of ASME, Journal of Engineering Materials and Technology, Vol. 110, (1998) p. 344 [9] D.
Smith: Journal of Strain Analysis, Vol. 37 No. 2 (2002), p. 125 [10] A.A.
Fischer:International Journal of Mechanical Sciences, Vol. 43 (2001), p. 2281 Trans Tech Publications Ltd Brandrain 6 Fax: +41 - 1 922 10 33 CH-8707 Uetikon-Zuerich e-mail: ttp@ttp.net Switzerland Web: http://www.ttp.net

Introduction Drilling is the process of creating or widening a circular crosswise hole in solid materials such as metal sheets, polymers, chemical compound composites, and building materials, as well as in the construction industry.
Drilling is essential to creating rounded, cross-sectional holes in solid materials in aircraft industries.
In choosing drilling techniques and materials, researchers and manufacturers need to consider these factors.
CIRP Journal of Manufacturing Science and Technology, 4(1), (2011). p.57
Materials and Manufacturing Processes, 32(6), (2017) p. 623.