Search results

In Eq. (1), the six strain components are parameters to be calculated using least-square method if a sufficient number (more than six) of εΦΨ are obtained.
In Eq. (3), the direction-dependent X-ray elastic constants Ehkl can be determined by the Vook–Witt Grain Interaction Model [13].

The defects of the process were as follows: firstly，a high reaction temperature; secondly, a large number of wasted zinc powder; thirdly , dear and severe environmental pollution.
The Zn, Ni metallic grains were well-distributed on the surface of P-mSA membrane.

Technical specifications for construction of highway roadbases（JTG 034-2000）stipulates that: When using the cement stabilized soil as base in the pavement structure, for granular soil and coarse grained soil at the time of mixture composition design cement dosage should be 3~7%.
The number of each parallel mixture specimens was 6.

Improper soaking time and cooling time will make pull crack and big grain of casting [3,4].
Due to the large size table, the casting equipments, machining equipments, hoisting equipments and workshops used to make its also require large-scale corresponding, a number of large equipment and the plant will cause the high cost of production.

The author of this paper analyzed a large number of documents and data about active coke desulfurization, and discussed the reasons why does this technology not be used widely on the basis of the economic analysis.
Fig. 1 Samples of active coke In present, active coke is mainly used in removing of SO2 in flue gas using the moving bed, the range of iodine value of generic active coke is 400~500 mg/g, so this technology has a certain requirements to its sulfur capacity, strength and abrasion resistance, grain size, anti-drug resistance and anti-poisoning properties, as well as the adsorption process and the desorption rate.

The size of the agglomerated powder is about 30-40μm，Grain size of each phase is in the range of 50-500nm.
Upon impact, the liquid droplet can rebound, deposit, or splash, at least partially.These phenomena are related to critical values of the Sommerfeld parameter K of the particle at impact defined as：K=We1/2·Re1/4，where We and Re are the Weber and Reynolds numbers, respectively[11].

Most of such techniques lead to formation of highly developed dislocation/grain microstructures and cause compressive residual stresses, providing significant hardening in the material's surface layer and increasing resistance to fatigue, wear or corrosion[1].
A major problem for this field of research is the tremendous commercial interest in applying this technology as seen by the large number of patents produced by General Electric for turbine blade applications.

Introduction Perovskite-type structures can tolerate a range of different anions as well as a number of cation species.
Both the oxynitrides contained primary particles with grain sizes around 0.2mm.

Its value is to provide readers how much knowledge content, and not to provide service time or the number of offer.
[8] Xu Hong, Liu Guangli, Guo Jing, Lou Zhenlin, "Grain Price Impact Analysis System on Data Mining", JCIT, vol. 6, no. 1, pp. 207-211, 2011.

Halogenated hydrocarbon standard sample mixing 5 kinds of volatile (batch number of the standards: 332909 IERM); Zero-valence iron (Hardware Factory of He Bei University of Technology); KC-6 Activated carbon (Beijing KeCheng GuangHua New Technology Company); TiO2 were prepared by sol-gel method[[] Yilong Yang, Xiulan Xin, Daiqiang Hu, Shengjun Qin: Journal of Beijing Technology and Business University(Natural Science Edition),Vol.25(2007), p9 (In Chinese) ].
TiO2-EP mass [g] (c)The influence of TiO2 mass on the removal rate of CHCl3 The removal rate of CHCl3 [%] The removal rate of CHCl3 [%] Time [min] (a) The influence of iron grain size on the removal rate of CHCl3 Iron mass [g] The removal rate of CHCl3 [%] (b)The influence of iron mass on the removal rate of CHCl3 Time [min] The removal rate of CHCl3 [%] (d)The influence of AC mass on the removal rate of CHCl3 Fig.1.