Search results

An increase in zinc concentration leads to an increase in average grain size of formed nuclei and to a decrease in specific surface of zinc powder, which can negatively affect to subsequent gold cementation.
Apparently, elongated form of dendrites leads to a large number of voids between individual particles.

The addition of ATT increases the water absorption rate because ATT is a porous material and contains a large number of hydroxyl groups with relatively hydrophilic groups.
Evaluating distillers grains as bio-fillers for high-density polyethylene[J].

Recently, a number of research works connected with development and investigation of various ways of heat removal from the tool have been carried out.
Application of this cooling system has provided for an increase of the peak speed of cemented hard steel 20Х (55 HRC) burnishing by the tool with the indenter tip made from ultra-fine grain cubic boron nitride (DBN) up to 20 m/min.

(Table 2) Table 1 Ecological capacity of yantai based on energy value(2008) Projet Raw data （j） Energy conversion rate（sej／j） Solar energy （sej） Per capita energy （sej） Per capita capacity （hm2） Solar energy 1.47E+20 1E+0 1.47E+20 2.256E+13 0.073 Wind power 1.93E+17 6.63E+2 1.28E+20 1.964E+13 0.063 Rain potential 3.92E+15 8.88E+3 3.484E+19 5.346E+12 0.0172 Rain compounds 3.89E+15 1.82E+4 7.08E+20 1.086E+14 0.35 Earth rotates energy 1.567.16 2.90E+4 4.54E+20 6.973E+13 0.225 Tidal energy 1.34E+16 2.365E+14 3.169E+20 4.863E+13 0.157 Ecological Capacity 1.0249E+21 0.507 Table 2 Ecological footprint of yantai based on the energy analysis(2008) Project Raw data （j） Energy conversion rate（sej／j） Solar energy（sej） Per capita energy （sej） Per capita the ecological footprint（hm2） Land type Biological resources 11.847 Grain 2.407E+16 8.3E+4 1.998E+21 3.066E+14 0.411 Farmland Vegetables 2.657E+16 2.7E+4 7.174E+20 1.101E+14 0.148 Farmland Melons 4.352E+16 5.30E+4 2.307E
The forest coverage rate would be much less if the number of fruit trees were deducted from the forest

The force values (N) for particular penetration depth of the brush measured for 8 tools Penetration depth Δ Value of dynamic radius Dd/2 (mm) 62,6 62,8 62,2 62,4 62,6 62,5 62,3 62,3 (mm) Force F (N) 0 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,3 0,2 0,2 0,3 0,2 0,3 0,3 0,2 0,2 0,6 0,4 0,5 0,6 0,5 0,7 0,7 0,4 0,3 0,9 0,8 0,8 0,9 0,7 1,1 1,1 0,6 0,5 1,7 1,9 1,4 1,7 1,3 2 2,2 1,4 1 4,6 5 3,6 4,3 3,7 5,5 4,9 3,8 3 22 23 18,1 21 25 28,6 28 22,1 Tool number 1 2 3 4 5 6 7 8 As to repeatability of results after brushing, it is important that for the particular value of penetration depth, after brush change to new one, the forces will have the same values for all brushes of the same type.
Lal, Experimental investigation into cutting forces and active grain density during abrasive flow machining, International Journal of Machine Tools and Manufacture, 44, 2-3 (2004) 201-211

At present, modern surface engineering techniques have been extensively applied to a good number of industrial fields concerning national economy.
In detail, there are the following factors that affect atmospheric corrosion, i.e., relative humidity, temperature, difference in temperature, acerbity, alkali, salt, corrosive gases, solid grains, and state of metal surface and so on.

In our model, the minimum number of layers to achieve a good fit was chosen [6].
This is consistent with larger grain size and thus lower resistance than NiSix obtained from an RF sputter preclean.

The images indicate better dispersion of Ag with less agglomeration throughout its surface and also indicate that the silver nanoparticles are homogeneously distributed in TiO2 grains.
It is seen that the coating thicknesses varied with different ceramic substrates composition though coated with the same number of layers.

Introduction Cemented carbide (WC-Co) consists of tungsten carbide grains embedded in a metal binder phase.
Although the difference in WC and Co wt-% is not so significant between both cases, it is found that the best sample is number 3, powder denoted as 250-60 (for rotation speed 250rpm and 60 minutes).

Due to these specific properties, AlN thin films have drawn considerable interest and large numbers of publications have been devoted on their film preparations under various substrates.
The grain sizes tended to decrease significantly when increasing CN.