Search results

The optical properties using UV-Vis in thin films of antimony tin oxide doping show samples including semiconductor materials that can be used as electronic devices as seen from the reduction of this energy gap from 3.680 to 3.574 eV.
The data from the band gap energy corresponds to the results of the SEM testing coupeled with EDX where it is seen that the smooth surface of the samples shows a low band gap energy so that the conductivity is higher.

These patients need the reduction in knee joint pain because this is crucial to minimize the reflex inhibition and restore normal joint activity.
In the case where the effects of particle size reduction, polymer hydrophilicity and wettability have been assumed to be the same, the major contribution to the dissolution enhancement has appeared to be due to intermolecular interactions between the drug and the polymer [3].
During normal operation, the current positions of the Traverse Unit datum (X axis position) and the height of the Stylus (Z axis) are displayed.

In this paper, data concerning the effect of pH towards the development of TiO2 nanoparticles is reported.
Most samples showed fast degradation within first 2 hours as more than 90% of MO degradated by sample C400-5, C400-7 and C400-9 while sample C400-3 and C400-1 show 79% reduction and 62% respectively.

Structural optimization design of body of Oil-perforating gun Ming-ju ZHAO1,a Gong-zhi ZHU2,b 1Jilin Institute of Chemical technology, Jilin 132022,China 2Dalian Maritime University, Dalian 116026, China azmj@jlict.edu.cn b908718532@qq.com Key Words: Oil-perforating gun; gun block; blind hole; optimization ; ANSYS Abstract: In the design of structure of oil perforating gun, for on the depth of perforating gun blind hole diameter, and the gun body wall thickness design is the key technology, through the introduction of optimization design technology, under the condition of satisfy the use requirement, language APDL of ANSYS software parametric optimal design of several data, the minimum wall thickness can get a gun.
However, as a result of the existence of blind holes, make the gun body wall thickness reduction, reducing the intensity of the perforating gun in blind holes.

Normalized values of Felicity Ratio were plotted and compared with the nonlinear ultrasonic test data.
For damage level above 40% the reduction in amplitude was larger.

The crystallite size and lattice parameters for each sample were determined from X-Ray diffraction data using Scherrer’s formula.
As expected the reduction in particle size gives a shift in the optical band gap of the films.

Based on Xinjiang Production and Construction Corps (XPCC) statistical data from 1978 to 2012, the paper, by employing industrial structure deviation degree and structure coordination coefficient, conducts an analysis on the change tendency of and correlation between XPCC industry structure and employment structure.
The need for workforce is inversely proportional to the relative productivity promotion of secondary industry resulting in reduction of employment.

Their properties have been characterized on the basis of the experimental data obtained using thermal analysis (DSC/TGA, X-ray diffraction and scanning electron microscopy (SEM).
Analyzing the XRD data, two major differences become obvious when comparing the samples loaded by the smaller and larger amount of Al2O3.
These data demonstrate a strong dependence of the formation of evaporation of absorbed water on the load of Al2O3 and shows that an increase of the load leads a reduction of evaporation of absorbed water.

The standalone digital twin has been validated using real data and allows one to perform what-if simulations in real time.
A Discrete Event Simulation (DES) model will allow simulations to be performed, obtain, and process data from data sources and Enterprise Resource Planning (ERP), and use them to make future decisions.
In this way, the DT will be connected to an MES system, which is one of the most suitable tools for solving problems related to data storage, saving planning time and avoiding manual data entry.
One of the greatest complexities arises from the maintenance of a data connection system.
Data availability Statement The research data associated with this paper is available upon request to the authors.

So, e.g. for Germany some programs are running focusing on the reduction of CO2 emission for primary industries, such as metal and chemical plants as well as electrical power plants or even the field of automotive and transportation.
Besides the optimization of the power train and the improvement of the engine, the reduction of the body-in-white weight gives a major input to reach the goal.
The bonding process was performed without a thickness reduction of the core and the cover sheets.
So, data such as forming limit curves (FLC), mechanical properties under tensile/axial/bending load and failure conditions have to be investigated and classified to be able to develop rules for the use of such sandwiches.
[13] ALUCOBOND - 3A Composites GMbH. http://www.alucobond.com/alucobond-technical-data.html