Search results

Specifications of grinding wheel and grinding parameters Parameters Value Average grain size(μm) 75 Grade R Concentration number 75 cutting speed (vc)(m/s) 30 Feedrate (vw)(mm/s) 413 Depth of cut (ap) (μm) 4 Residual Stress Measurement In this study, X-ray diffraction (XRD) technique using sin2ψ method was utilized to measure surface residual stresses.

Numbers of pyrolysis studies have been carried out based on combined feedstock such as sewage sludge with rice waste [3] and sugarcane bagasse with petroleum residue [4].
Then, dried coconut shells and rice husks were grinded into powder with grain size of (<1 mm).

Calculated fir tensile strength in the saturated state is only lower than the average air-dry state of 4.1% and 5.5% lower, than the average of pine, far less than the moisture content effect of grain of the macro-tensile strength. 
Fig. 2 Longitudinal tensile strength Fig. 3 Longitudinal tensile strength of of Chinese fir tracheids Masson pine tracheids Pine wood tracheid longitudinal tensile strength after heat treatment Table 2 Zero-span tensile strength of the tracheids of heat-treated Masson-Pine Treatment level 160℃(2h) 180℃(2h) 180℃(3h) 180℃(4h) 200℃(2h) 220℃(4h) Number of samples  23 24 24 24 24 14 Max /MPa 415 445 387 392 380 268 Minimum /MPa 354 364 323 330 320 217 Average/MPa 384 395 364 357 343 242 Standard deviation 16.018 26.563 18.812 15.441 13.238 17.451 Coefficient of variation/% 4.17 6.72 5.17 4.32 3.86 7.19 After heat treatment, longitudinal tensile strength of fir and pine’s earlywood has been reduced in comparison with the control samples, and pine wood decreased more significantly.

Moreover, the kitchen should be big enough to store all kinds of food and goods including tablewares, cookers, seasonings, grains, dried food, fruits, vegetables and drinks, and they should be easy to reach.
The references are to be numbered in the order in which they are cited in the text and are to be listed at the end of the contribution under a heading References, see our example below.

Introduction In recent years, a large number of research results indicate that Graphics Processor Unit (GPU) has great advantage compared with the CPU in solving compute-intensive problems [1].
This mixed programming model can leverage both MPI programming and OpenMP programming: MPI for coarse-grained communication between processors or nodes, and OpenMP for inter-processor communication of a multi-processor computer.

The particle size and the crystalline structure of the product samples were detected by means of X-ray analysis with a BD-86 diffractometer(Japan) and Mastersizer 2000 Laser grain-size analysis meter(England).
The radius of iron is similar to titanium, Fe3+ can go into the lattice of TiO2, insteading of Ti4+, improve the number of oxygen vacancies between surface and inner of the lattice of TiO2.

Subsurface excavation damages to the surroundings in various degrees and results in many negative impacts, such as surface settlement in city, underground reservoir’s decrease,earthfall or landslide,which will inevitably lead to a large number of surface damage to buildings and facilities,constructor’s casualties and water environmen’s deterioration.The Subsurface excavation even leads to geologic hazard,( such as geodynamic release, earthquake, underground cross-off induced by urban underground empty) which will seriously affected the city’s working and sustainable development[2].
Some partial section is filled-type structural development and it will be cutting as rock base’s corase-grained granite.

., they tend to be enriched at grain boundaries and/or phase boundaries for their relative large atomic radius and thus improve the microstructure stability of the solder.
Besides shearing/inflow collision, Brownian motion can also cause an increase to the number of aggregates in the system.

The cemented carbide produced by ultra-fine cobalt powder can reduce the porosity and avoid the formation of cobalt pool, which can separate WC grains.
When the temperature rises to 700°C, the product contains a large number of ß-Co with the proportion of ɑ-Co and ß-Co of 1:1 approximately.

In the modern world, forging process is applied by sets of die and tooling which deliver the compressive force to form desire shape from simple billet [2] This compressive force used in forming the parts, allows the grain to be aligned with the die contours which made the part to have a superior strength compared to casting and machining process [3].
This Simulation software package also allows the forgers to test a number of “what if” scenarios and determines the optimum condition without having to test-run the die [4].