Search results

Based on Faraday's Laws of Electrolysis, the reduction in wheel radius (wheel wear) is a function of the electrical charge.
The control scheme was based on optimal dressing data.
Reduction of grinding forces by applying ELID.
Reduction in grinding forces reported. [57] Sintered SiC, Zerodur, CVD-SiC Subsurface effects investigated.
The reduction in grinding forces is favourable because sub-surface damage is reduced and surface integrity is enhanced.

All the gathered data should allow an interpretation of the gradual change in time of the structure’s physical reality, of its technological conception and of its structural behaviour since the original design by the carpenter or engineer, through the subsequent works or “natural” evolutions, unto the current state.
Instead, with regard to the investigations that are carried out locally only, the choice of the points in which execute them is even more crucial, since it is necessary that collected data are significant for the entire structure or for specific critical points (e.g. measurement of moisture content).
The survey of the geometry of the structure The detailed survey should not be only a gathering of metric data about the geometry of the structure and it should not only provide a graphic support for recording data of subsequent investigations: it must be the first step towards the critical interpretation of the structural complex.
On the other hand, the use of thermography can provide only qualitative data, but in a simpler way, thus being useful for identifying critical areas in which to perform the measurements with electrical resistance hygrometer.
All gathered data should allow an interpretation of the gradual change in time of the structure’s physical reality, its technological conception and its structural behaviour since the original design, through the subsequent works or “natural” evolutions, unto the current state.

Grain growth is driven by the reduction in grain boundary surface area, and takes place via grain boundary migration.
According to above equations, the relationship between the grain size and holding time were analyzed by means of data fitting.
The relationship between and can be obtained by means of linear fit of above datum, as shown in Fig.5.
The experimental data of this paper will be helpful to further investigate the structure evolvement of HAZ for the 12%Cr ferritic stainless steel.

Application of Basic Grey Model Data Fitting of Complete Load-Settlement Curves of Pile Tests.
In this work, loading tests data of totally over one hundred piles were collected.
Table 1 Data summary of pile loading tests No.
The errors of the data of last load step between the data from two approaches were 39%, 57% and 4%, which indicates that the prediction precisions are largely discrete and unacceptable.
Thus, the prediction results repeated the characteristics of the given data.

Research method diagram This scientific article's title is based on data analysis by Vosviewer, which identifies scientific works that have not undergone extensive research.
The national goal is to reduce carbon emissions from buildings because they are significant in carbon reduction plans.
Comparison between building and environment Development causes a reduction in land, which damages the environmental ecosystem.
Gaffney et al., "Maximizing value of genetic sequence data requires an enabling environment and urgency," Glob Food Sec, vol. 33, 2022, doi: 10.1016/j.gfs.2022.100619
Han, "Trend analysis on adoption of virtual and augmented reality in the architecture, engineering, and construction industry," Data (Basel), 2020, [Online].

Based on the data of the band structure, DOS (Density of State) and PDOS( Partial Density of States), atomic populations and net charge, the influence on the energy band structure of the macrostructure of ZnO and La-doped ZnO was investigated.
It was assigned to the reduction of energy transfer which was caused by the gathering of rare earth ions in the boundary of grain and also the weak interaction of charge carriers and doping ions due to the lower solubility of rare earth ions in the ZnO materials [8].

The study not only provides useful data concerning the structural safety of the Guangzhou New TV Tower during construction but also is of considerable referential importance in estimating the safety of an in-construction supertall structure.
The procedure of model reduction and tuning, the element mass and stiffness matrices and the global mass and stiffness matrices of the reduced model can be downloaded at http://www.cse.polyu.edu.hk/benchmark/Phase 1 date/system matrices.mat.

The major problem for forging of magnesium alloy is the lack of basic process data, such as strength and ductility.
Extruded materials Mg96Zn2Y2 (Mg-2%Zn-2%Y) Reduction R10 Size (mm) Φ8×12 Temperature (°C) 25, 100, 150, 200, 250, 300, 350, 400, 450 Speed (mm/min) 5,10,50,100 Lubricant No Experimental results Figure 1 shows the flow stress curves of Mg96Zn2Y2 alloy (R10) with a processing speed of 5mm/min under various temperatures (from 20°C -450°C).

XRD data were received using a Rigaku D/MAX-3B diffractometer with Cu Ka target radiated at 45 kV and 150 mA.
Substituting the value of A in Eq. (8) and using the flow stress data at various strains for the same flow curves, ln(σ-A) vs. lnε is plotted.
Some typical experimental and predicted data are shown in Fig. 3a in which also contains the data for the quasi-static testing.
Comparisons between the experimental and the predicted data at various deformation conditions shown in Fig. 3, it can be found that a small deviation between the experimental data and the predicted data can be received in most of the deformation conditions.
From the data shown in Fig. 2a for the two specimens, it can be seen obviously that the correlation between the experimental data and the predicted data for the former is better than that the latter.

In fact it is used in any communication system that transmits and receives data on a high frequency carrier for producing the carrier.
[5] A.Chenakin, “phase noise reduction in microwave oscillators, ”Phase Matrix Inc., San Jose, CA, microwave journal vol. 52, no., October 2009