Search results

Journal of Food Composition and Analysis, 2008, 21(4): 326-331
Seed Science Research, 2000, 10(1): 11-34
Advanced Materials Research, 2012, 535: 1126-1132
Agronomy Journal, 1975, 67(4): 541-544
Science of the total environment, 1999, 231(1): 53-65

The mistake is pointed out finally, and correcting until no wrinkling and cracking. 1.2 Expanding blank using DYNAFORM Choosing the material DQSK,its’ thickness is 1.2mm,as Fig2.
Fig2 The workpiece and its’ material Then output compounding(using igs format),as Fig3,it also can be input UG for the next step.
Acknowledgements The national natural science foundation of china(30972399) ;"Eleventh Five-Year" plan supported by key project of National Science and Technology (2009BADB1B0304-5)；Scientific research financial project aided by education department of Hunan Province（09C1017）.
Journal of Engineering Design，2008，15（1）：77-78.
Die design method for sheet spring back, International Journal of Mechanical Sciences,2004,46(7):1097-1113

Materials and methods Elemental analysis.
Journal of hazardous materials, 2008. 159(2): p. 390-395
Advanced Materials Research, 2012. 599: p. 929-933
Journal of materials science, 2007. 42(7): p. 2226-2230
Journal of hazardous materials, 2012. 207: p. 44-50.

Acknowledgement The authors acknowledge the support from National Science Foundation of P.R.
Advani: Journal of Composite Materials Vol. 35 (2001), p.713 [5] A.Q.
Tamma: International Journal of Heat and Mass Transfer Vol. 44(2001), p.3135 [8] B.R Gedart: Journal of Composite Materials Vol. 26 (2006), p.1100 [9] J.F.
Hwang: Journal of Composite Materials Vol. 42 (2008), p. 909 [10] N.D.
Tamma: International Journal for Numerical Methods in Engineering Vol. 60 (2004), p.1741

It is efficient cutting methods for high-precision thin-hole machining of hardened materials, Introduction Reaming is one of the important methods for high-precision thin hole processing.
THE CUTTING EDGE MATERIAL OF THE REAMER IS YG8.
Thirdly, the material of the test work piece is 45 steel.
The generated regular impulse force is acted on the test materials.
Li, L.W,Gao and T.H,Zhang: Journal of Jiamusi University( Natural Science Edition), Vol . 18 (2008) No. 4.p.326 [8] Chandra Nath and M.Rahman: International Journal of Machining Tools & Manufacture, 2008, No.48.p 965.

Experiments Materials.
It plays a role in diluting cement after replacing cement equivalently, in order to reduce the water demand of cementitious materials.
However, if the specific surface area is too large, after limestone powder replaces cement, the particle volume of cementitious materials may increase, which increases the water demand of cementitious materials.The limestone powder used in this experiment has larger specific surface area and smaller particles.
Bernier: Materials and Structures Vol. 29 (1996), p. 233 [2] Olivier Bonneau, Mohamed Lachemi and Eric Dallaire: ACI Materials Journal Vol. 94 (1997), p. 286 [3] Pierre Y.
Blais and Marco Couture: PCI Journal (1999), p. 60 [4] Z.

Introduction Epoxy resins have been extensively used in a variety of wide industrial applications, such as surface coatings, adhesives, painting materials as well as microelectronic encapsulated materials owing to their excellent mechanical properties, electronic properties, adhesion, solvent and chemical resistance.
Experimental Materials.
Influences of contents of organic silicone on the matrix were investigated via measuring the tensile strength and elongation, thermal stability and microstructure of the cured materials.
Huang: Journal of Polymer Science, Vol. 34 (1996), p. 1907-1922 [3] S.T.
Huang: Journal of Applied Polymer Science Vol. 62 (1996), p. 1641-1649 [4] I.

Test Materials and Test Method 1.
Test Materials.
[7] Zhu Beibei, Yang Quanbing: Study on Surface Thermal Activation of Coal-Gangue, Journal of Building Materials, 9（4）, (2006), p 484-487
[9] Guo Wei, Li Dongxu, Chen Jianhua, et al: Changes in Minerial Composition and Structure of Coal Gangue During Heat Activation, Joural of Materials Science and Engineering, 26（2）, (2008), p 204-207
[14]Peelamedu R D, Roy R, Agrawal D K: Anisothermal Reaction Synthesis of Garnets, Ferrites and Spinels in Microwave Field [J], Materials Research Buletin,36 (2001), p2723-2739

Journal of Materials Research.
Materials Science and Engineering. 2006.
Mechanics of Materials.
Deformation and Materials Failure. 2010. №2, p. 43-48.
Materials and Desing.

Creep-Feed Grinding of Tungsten Carbide by Using Resin-Bonded Nickel-Coated Diamond Wheel Abbas Pak1, a, Amir Abdullah2, b 1Department of Mechanical Engineering, Manufacturing Group, Iran University of Science and Technology- Arak branch, Arak, I.R of IRAN.
Force and specific energy are important factors in all abrasive machining operations especially in creep-feed grinding of hard materials.
Introduction Cemented tungsten carbide is a very tough composite material, with completely different behavior from steels and other ordinary materials.
This paper tries to investigate the effects of parameters of creep-feed grinding of this material.
Tools Manufac., 37(8) (1997). [3] Tso Pei-Lim, and Yang San-Yeng, The Compensation of Geometrical Error on Forming Grinding, Journal of Materials Processing Technology 73 (1998). [4] C.