Search results

In order to save material of SMA, both sides of the supports are made of general steel plate.
When preload force of sliding bolt is large enough, the maximum tension of SMA support significantly increases and hysteretic loop is relatively narrow, showing good super- elastic properties which is consistent with constitutive curve of SMA materials
References [1] Junfeng Hou, Sanqing Su, Sheliang Wang: Chinese Journal of Xi’an University of Science and Technology, Vol. 29(2009), p. 49-53, in Chinese [2] Bin Wu, Jigang Zhang, M.S.Williams, Jinping Ou: Engineering Structures, Vol. 27(2005), p. 1258-1267
[3] Biyu Zheng, Zejin Shang, Zhongmin Wang: Chinese Journal of Mechanical Science and Technology, Vol. 27(2008), p. 1236-1238,1242, in Chinese
[4] Jigang Zhang, Aizhen Lu and Jinping Ou: Chinese Journal of Beijing University of Technology, in press, in Chinese [5] Chinese Seismic Design of Buildings (GB50011-2010) , in Chinese

Sciences Wiesbaden, Dept. for Mech.
Introduction The behavior of most materials is influenced by inhomogeneously distributed microscale properties.
For microstretch materials, an isotropically deforming vector triad is attached to each material point of the body under consideration to describe its microstructure.
First Numerical Results As to date, numerical results for engineering problems involving microstretch materials are not available in the literature, one of our foremost aims is the demonstration of a downward compatibitlity of microstretch materials to polar materials (so that by switching of all stretch-related effects, results can be counterchecked with those for polar continua).
Journal of Sound and Vibration (2002), Vol. 250, p. 711 [11] Singh B.

Mentioned that TiO2 was mostly applied as pigments, filters, adsorbents, catalyst supports, photoconductors ,coatings, and dielectric materials.
Bilik and Plesch, 2007 [6] reported that the size of the TiO2 particles is a key factor affecting the performance of the materials.
Even using different amount of the starting materials, the obtained powder size is different for the same route (Li et al.,2002) [7].
Firstly, the stoichiometric measurements of the starting materials were weighed out.
The gel preparation process was started when the starting materials are dissolved in absolute ethanol under vigorous stirring.

Study on the Properties of Polyphenylene Sulfide/Nano-Zinc Oxide Composites Neng Wan1[+], Wei-Hua Yao2[+], Jui-Chen Chen2, Juan Du1, Manuel Reyes De Guzman1,3,4, Chi-Hui Tsou1,3,4,a* 1*Material Corrosion and Protection Key Laboratory of Sichuan Province, Materials and Science Engineering Laboratory of Sichuan Province, School of Materials Science and Engineering, Sichuan University of Science and Engineering, Zigong, 643000, China 2Department of Materials and Textiles, Oriental Institute of Technology, Pan-Chiao 22064, Taiwan; 3Sichuan Zhirenfa Environmental Protection Technology Co., Ltd, Zigong 610051, China 4Sichuan zhixiangyi Technology Co., Ltd, Chendu, China a*mayko0301@hotmail.com [+] These authors contributed equally to this work.
Figure 1 XRD images of nanozinc oxidation properties 2 Experimental 2-1 Materials and Instruments Industrial grade CB602 PPS was supplied by Sichuan Zhongke Xingye Materials Co., Ltd.
Journal of Applied Polymer Science. 109. (2008) 720 - 726
Journal of Applied Physics. (2004). 95. 661-666
Materials Science and Engineering: C. . (2018) .90

Alberto Lamego, 2000, 28013-602, Campos dos Goytacazes, Brazil. 2 - Mineral Technology Center - CETEM/MCTI, Regional Nucleous of the Espirito Santo, Rodovia Cachoeiro-Alegre, km 5, bloco 10, Morro Grande- Cachoeiro de Itapemirim, Brazil. 3 - IME - Military Institute of Engineering, Department of Materials Science, Praça General Tibúrcio, 80, 22290-270, Rio de Janeiro, Brazil.
Upon arrival at the Advance Materials Laboratory, LAMAV, of the State University of North Rio de Janeiro, UENF, the waste was dried in a stove at 110°C for 24 hours.
In this table one should note that both materials present higher SiO2 and Al2O3 contents.
Monteiro: Materials Science and Engineering A.
Acchar: Applied Clay Science Vol. 30 (2005), p.42

Materials Letters nº41, 1999, p. 153-158
Upadhyaya: Effect of YAG Addition on Sintering of P/M 316L and 434L Stainless Steel, Materials Letters nº 58, 2004, p. 2037-2040
L.; Synthesis and Processing of Nanostructured WC-Co Materials, Journal of Materials Science, n 37, p. 3397-3403, 2002
Marcè: Reinforcing 316L stainless steel with intermetallic and carbide particles, Materials Science and Engineering A 335, 2002, p. 1-5
In: Materiais - IV International Materials Symposium, Porto, 2007, (to be publishing)

The material is composed of propane, which contains hydroxyl group at position 1 and 2.
By this method, the paper-based silver nanoparticles are good to be used as antimicrobial materials.
Chemical Engineering Journal, Vol. 228 (2013), pp.596–613
European Journal of Pharmaceutics and Biopharmaceutics Vol. 127 (2018), pp.130–141
Journal of Nanoscience and Nanotechnology Vol. 9 (2009), pp.3067–3074

Different materials were adopted to simulate the roughness of saltation snow particles to get the distribution of wind velocity in the simple wind tunnel.
In this paper, different roughness materials are adopted to simulate saltation snow particles (Fig.1) so that velocity distribution in saltation layer can be gained.
Light difference appears among the velocity profiles for three different roughness materials.
Journal of Wind Engineering and Industrial Aerodynamics, 2003. 91: p. 551-569. 2.
Key Engineering Materials, 2010 accepted. 6.

· Laser intensity: The laser has to be capable of scanning many different materials, which include characteristics such as color, material finish, surface quality and surface reflectivity.
The usual value of minimum signal strength is 50 when scanning shiny materials the peak might not reach 50 so a smaller value is recommended.
The industrial partner implanted following activities: · Geometric benchmarking: suspension layout, number of parts materials used and fitment sequences were identified
Thompson, “Predicting product aesthetic quality using virtual environments,” Journal of Computing and Information Science in Engineering,Vol. 1(2), 2001, pp. 105–112
Humphreys “Early supplier involvement in the design process:lessons from the electtronics industry,” The international Journal of Management Science, 2004, pp.179-199

(b) During laser re-melting, the coatings of Al2O3/Cr compound materials produce analogous martensitic phase transition, therefore, the strengthening of Al2O3/Cr compound material by laser re-melting comes from fine-grain strengthening by Cr-alloy martensitic phase transition partly
(2) The main strengthening mechanism of metal-based compound materials is that the load is transferred to reinforcement from the substrate, and reinforcement is a primary undertaker of load, the mechanism of load transfer is a key strengthening factor.
Zhuang: Ordnance Material Science and Engineering Vol. 23 (2000), p.7
Zhao: Laser Journal, Vol. 25 (2004), p.76
Chen: Journal of the Chinese Ceramic Society, Vol. 28 (2000), p.133