Search results

McEvily,Metallurgical Transactions A (Physical Metallurgy and Materials Science) Vol.13A(1982),p.439-445
Journal of Engineering Materials and Technology Vol.108(1986),p.174-178
,Metallurgical Transactions A (Physical Metallurgy and Materials Science) Vol.18A(1987),p.1291-8
Sadasue,Materials Science and Engineering A Vol.468-470(2007),p.114-119
Mutoh,Materials Science and Engineering A Vol.527(2010),p.2592-2597

Furthermore, the results also suggested that the floor materials should be selected to avoid the slip accidents.
Introduction Manual materials handling (MMH) can be often seen in the workplace.
Once the platform and walkway are covered with subjected floor materials, the floor COF values could be measured, and participants were requested to walk on the ramps to perform the experiment.
Chaffin, “A computerized biomechanical model- Development of and use in studying gross body actions,“ Journal of Biomechanics Vol. 2 (1969), p. 429-441
Pope, “City bus driving and low back pain: a study of the exposures to posture demands, manual materials handling and whole-body vibration,“ Applied Ergonomics Vol. 38 (2007), p. 29-38

Acknowledgements This work was financially supported by Guangxi Natural Science Foundation (2012GXNSFBA053147), Guangxi Educational Committee Science Foundation (Grant No. 201106LX592), Hechi University Science Foundation (Grant No.2011A-N001) and Guangxi Graduate Student Research Innovation Foundation (2011105950802M01) References [1] L.
Duszczyk: submitted to Journal of Materials Processing Technology (2006) [2] L.F.
Mao: Advanced Materials Research (2010) [3] K.Droder, Ph.D.Dissertation, IF-UM, University of Hanover (1999) [4] A.Wahab E.L.
Morsy, K.I Manabe: submitted to Journal of Materials Research (2006) [5] L.F.
Jensen: submitted to Journal of Materials Processing Technology (2000) [7] K.

Introduction One of the mechanical properties of high polymeric materials is their temperature sensitivity.
Experimental Analysis In this paper, high polymeric materials PVC sheet with precast defects was stretched under a uniaxial load.
Yu: Journal of Hebei University of Science and Technology, Vol. 24, No. 1 (2003), p. 35 (in Chinese) [4] E.D.
Journal of Circuits, Systems and Signal Processing, Vol. 1, No.1 (2007), p. 54 [5] D.Y.
Yang: Journal of Central South University of Forestry and Technology, Vol. 11, No. 11 (2010), p. 78 (in Chinese).

Injection molding defects not only affect appearance quality of products, and also reflect inappropriate choice of process conditions, molds and molding materials.
As a result of a wide variety of plastic raw materials, the structure of complex mold cavity, the different operating status of molding equipment, as well as the differences in molding material rheology, mechanical properties, and plastic products will have a variety of molding defects.
Journal of Colloidal Science. 6,(1951), p. 118 [2] Lin Dekuan, Ma Tianbao.
Journal of China Plastics.12 (2005), p. 21 [6] X.
Advanced Materials Research. 11-12(2006), p. 705

Introduction Urethane elastomers are promising materials for one-component sealants production.
This feature of the main monomer determines the variety of types of chemical bonds in polymer chains and their further transformations, which allows to obtain materials with various properties within the same class of polyurethane compounds.
The use of compounds based on Schiff bases as cross-linking agents allows to cure polyurethane sealants to be cured when interacting with air moisture without emitting carbon dioxide, which contributes to the production of defect-free materials.
The curing of sealing materials (SM) depends on several factors, including temperature, humidity and activator properties [12-13].
Tarasov, Hydrolysis of some Schiff bases, Journal of Applied Chemistry. 59 (1986) 1818-1822

Experiment Materials 60-mesh waste rubber, was purchased from a Nantong Huili Rubber Co..LTD.
Polymer Materials Science & Engineering, 2012, 28 (10): 102-105
Journal of applied polymer science, 1999, 73(14): 2951-2958
Journal of Applied polymer
Journal of Chemical Physics, 1943, 11(11): 521-527.

The Mie-Gruneisen equation [7,8] of state,which is described as follows, is applied as the state equation of metal materials.
Parameters for the state equation of the two metal materials are shown in Table 1
The displaced target materials increase and heap up continually with the keeping penetrating of the bullet.
Computational simulation of the hypervelocity impact of Al-sphere on thin plates of different materials [J], International Journal of Impact Engineering, 1997, 20(1-5): 363-374
Journal of Computational Physics, 1989, 82:1-15

Study on the wear resistance Of ZnAl27 composite reinforced by SiC particles Xie Jingpei1,a, Yan shuqing2,b, Wang Aiqin1,c, Wang Wenyan1,, Li Giwen1, Li Xiaoli1 1- School of Material Science and Engineering, Henan University of Science and Technology, Luoyang 471003, China. 2-The Key Laboratory of Material physics, Ministry of Education, Zhengzhou University, Zhengzhou Henan 450052, China aE-mail: xiejp@mail.haust.edu.cn, bE-mail: yanshuqing1979@163.com, cE-mail: aiqin_wang888@163.com Key words: Zinc-based allay; SiC particle; CuZn4 compounds, wear resistance Abstract.
Experimental material and methods 2.1 Experimental materials In the present work, the ZA27 alloy with the following composition was used: Al: 25-28wt.%, Cu: 1.25-1.75 wt.%, Mg: 0.01-0.15wt.% and balance Zn.
The investigation on Zinc-based composite [J], Materials Review, 1994(1):62-67. 3.
Journal of Metals, 1985 37(11):43-47. 5.
Journal of Materials science, 1992 27:1212-1216. 6.

Experimental Section Materials.
The results of this investigation are published in the journal Advanced Materials.
Soucek, “Preparation and characterization of monodisperse cerium oxide nanoparticles in hydrocarbon solvents,” Chemistry of Materials, 19, (2007) 1103–1110
Chen, “Effect of methanol-containing additive on the emission of carbonyl compounds from a heavy-duty diesel engine,” Journal of Hazardous Materials, 73 (2000) 39– 54
Pratsinis, “Flame-made ceria nanoparticles,” Journal of Materials Research, 17 (2008) 1356–1362.