Search results

Texture Changes of Asymmetrically Rolled AA 1050 Al Alloy Sheets Jin Hyuk Lee1,a and Insoo Kim1,b 1 Kumoh National Institute of Technology, School of Advanced Materials Science and Engineering, Gumi, Gyung Buk 730-701, Korea aljh1269@naver.com, biskim@kumoh.ac.kr (corresponding author) Keywords: Formability, Texture, ODF, Asymmetry rolling, Plastic Strain Ratio, R-value Abstract.
Forum, 254/256 (2010) 1259
Park, Advanced Mater., Research, 26/28 (2007) 393

Acknowledgement A part of this study was supported by Priority Assistance for the Formation of Worldwide Renowned Centers of Research - The Global COE Program (Project: Center of Excellence for Advanced Structural and Functional Materials Design) from the Ministry of Education, Culture, Sports, Science and Technology (MEXT), Japan.
New Frontiers of Process Science and Engineering in Advanced Materials Part 2, High Temperature Society Japan, (2004), p.233
Forum, 512(2005), p. 383

Kim 2,b 1 Department of Advanced Material Engineering, Sungkyunkwan University, 300 Chunchun-dong, Jangan-gu, Suwon, Gyunggi-do 440-746, Korea 2 Advanced Material Center, Korea Institute of Industrial Technology, 994-32 Dongchun-dong, Yeonsu-gu, Incheon 406-800, Korea a veryoon1@kitech.re.kr, bshae@kitech.re.kr Keywords: Thixoextrusion, AZ31 Mg wrought alloy, Extrusion pressure Abstract.
Forum Vol. 510-511 (2006), p. 362 [5] K.

Research on the System of Image Acquisition and Wireless Transmission Jiang Xiong1, a, Yong Pan1, b, Ziye Hou2, c, Ren Zhang2, d 1School of Computer Science, Chongqing Three Gorges University, Chongqing 404000 China 2 School of Electronic Information Engineering, Tianjin University, Tianjin 300072 China a xjcq123@yahoo.cn,bzhurongji_211@163.com, chouziye@tju.edu.cn, dzrjy@tju.edu.cn Keywords: Image acquisition; Wireless transmission; NRF24L01; STM32.
The basic forum is built in order to further verify many kinds of intelligent antenna algorithm, image processing algorithm and the network algorithm.
‘Image acquisition method based on TMS320DM642’, Advanced Design and Manufacturing Technology III, vol.397-400, pp.2196-2199, 2013
‘Design of wireless communication system based on nRF24L01’, Advanced Materials Research, vol. 945-949, pp. 1756-1759, 2014 [6] Pan Yong, Hou Ziye, Xiong Jiang, Liu Kaihua.

Effect of process parameters on the temperature of 4Cr9Si2 martensite refractory steel during CWR Jianghua Huanga, Jinping Liu, Baoyu Wang, Zhenghuan Hu School of Mechanical Engineering, University of Science and Technology Beijing, Beijing 10083, China ahjh79303416@126.com Keywords: 4Cr9Si2; Cross-Wedge Rolling (CWR); Process parameter; Temperature Abstract.
CWR is a high efficiency, low consumption, green advanced forming technology of shaft parts, compared with conventional cutting, forging process, with high production efficiency, material conservation and working conditions as well as good, CWR is recognized as an integral part of today’s advanced manufacturing technology [7].
Jeong, J.R.Cho and N.K.Lee: Materials science forum, Vol. 8 (2006), p.142

The electrical interconnections were established by the technology of electronic packaging and it is a major field in the electronic engineering.
Anderson, Lead-Free Soldering, Green and Sustainable Manufacturing of Advanced Material (2016) 101-134
Pharr, Measurement of mechanical properties by ultra-low load indentation, Material Science and Engineering 253 (1998) 151-159
Shin, Elastic, plastic and cracking indentation behaviour of silicon crystals, Material Science and Engineering 209 (1996) 91-96
Zulkifli, Hardness Variation of Ball Bond Wire Bonding, Advanced Materials Research 399-401 (2012) 1048–1051

Genzel: Advances in X-Ray Analysis 44, 247-256 (2001) [11] B.
Breidenstein: Advanced Engineering Materials 10, 7, 613-616 (2008) [12] B.
Breidenstein: Proceedings of the 6th International Conference THE Coatings in Manufacturing Engineering, Hannover, 33-42 (2007) [13] B.
Denkena and Breidenstein: Materials Science Forum 524-525, 607-612 (2006) [14] B.
Gerdes: Proceedings of the 7 th International Conference THE Coatings in Manufacturing Engineering, Kallithea-Chalkidiki, Greece, 29-38 (2008)

The proper balance between yield strength, YS, and ductile to brittle transition temperature, DBTT, has been the main concern during development of high strength engineering steels and the effect of microstructure on impact toughness has attracted a great attention during the last decades.
Introduction High-strength carbon steels exhibit yield strengths in the range 500 to 1000 MPa or even higher for advanced grades.
Guarnaschelli: Materials Science Forum, 638-642 (2010) p. 3188

Vinogradov, Electrolytic aluminizing of low-carbon steel in NaF-KF-AlF3 melt, Advanced Materials Research. 1088 (2015) 250
Electrolytic aluminizing of low carbon steel as protection treatment for current leads against high temperature oxidation, Materials Science Forum 844 (2016) 141-145
Kulevich, The structure and the phase composition of copper aluminide-based coatings formed on the aluminum surface under contact melting in the Al-Cu system joints, IOP Conference Series: Materials Science and Engineering. 177(1) (2017) 012110
Kulevich, Contact Melting Mechanism in the Cu-Ti System, Key Engineering Materials. 743 (2017) 58-62
Problems of Materials Science, Welding and Strength in Mechanical Engineering. 10 (205) (2017) 54-57.

Your Paper's Title Starts Here: Please Center use Helvetica (Arial) 14 Research on energy saving diagnosis of clean air conditioning system in pharmaceutical industry Xin Li 1 , a, Ruiying Jia1,b , Runping Niu2,c 1 Shenyang University, Institute of Architectural Engineering, Shenyang, China 2 Beijing University of Civil Engineering and Architecture, Beijing, China a55047430@qq.com, bjiaruiying6@163.com, cniurunping@bucea.edu.cn FULL First Author1, a, FULL Second Author2,b and Last Author3,c 1Full address of first author, including country 2Full address of second author, including country 3List all distinct addresses in the same way aemail, bemail, cemail Keywords: List the keywords covered in your paper.
References [1] Jieqing Jia, Air conditioning energy consumption diagnosis and fault diagnosis system (utility) method，Handan：Hebei University of Engineering (2011) [2] Qiuping Yu, Study on the influence factors of energy consumption of typical office building in Shanghai and its application in LEED standard,Shanghai：Donghua University(2011) [3] K.
The author should indicate on the checklist if he wishes to have them printed in full color and make the necessary payments in advance.
Forum Vol. 83-87 (1992), p. 119 [2] M.A.
Mishing, in: Diffusion Processes in Advanced Technological Materials, edtied by D.