Search results

By using TGA, Ramajo-Escalera et al. investigated sugarcane bagasse decomposition characteristics and kinetics [3].
Chen et el. evaluated the degradation kinetics of five lignocellulosic biomass (pine wood, fern stem, wheat stalk, sugasse, jute) in nitrogen atmosphere [4].
Fernanda Cristina Rezende Lopes et el. studied the thermal decomposition kinetics of guarana seed residue in synthetic air [5].

Xu, et al.
[3] El-Mekkawy, S., M.R.
Wu, et al.
Yao, et al.
Wu, et al.

Production of Ferrosilicoaluminium from Aluminum Slag and Local Ore via Carbothermic Reduction Azza Ahmed1*, Hoda El-Faramawy1 Saeed Ghali1 Michel L.
Al), single ferroalloys (i.e.
Omelchenko et.al
Meanwhile, a trial was done to use oxide residues of Al-slag waste in the production of AlSi alloy.
Al-Fe-Si (aluminum-iron-silicon), Journal of phase equilibria and diffusion 30. 2 (2009) 184-188

Y.Y.Chen et al. discovered that the general corrosion resistance of the FeCoNiCrAlSi HEA in aqueous solutions of NaCl and H2SO4 at ambient temperature is superior to that of 304S, irrespective of the concentration of electrolyte in the range 0.1–1 M.[5] Yu-Jui Hsu et al. reported that FeCoNiCrCux HEAs have much better corrosion resistant than 304L in 3.5% NaCl solution.[6] Y.L.
The type of alloy free corrosion potential，V free corrosion current density，I ，A/cm2 Al alloy Al-5%Zn-0.05%CeO2 [9] -0.935 2.839×10-5 Al-Zn-In [10] -1.01 7.1×10-6 Zn alloy* zinc-electroplated steel sheet [11] -1.02 3.28×10-5 Mg alloy Mg-9%Al-1%Zn [12] -1.52 2.91×10-3 AlMgZnSnPbCuMnNi high-entropy alloy -1.33 2.93×10-5 From table 2, we also can find that the Al, Zn or Mg content in the typical sacrificial anode materials is high level, which matches with the traditional concept.
It suggests that a new type of sacrificial anode materials with low free corrosion potential can be obtained with low level content of Al, Zn and Mg by proper composition design.
Although the content of Al, Zn and Mg component is far below than that of the typical sacrificial anode, the AlMgZnSnPbCuMnNi HEA has low free corrosion potential.
Vol. 53 (2011), p.1298 [11] Gamal Ahmed El-Mahdy, Atsushi Nishikata, Tooru Tsuru: Corros.

The manufacturing methods that used to fabricate metal-matrix are reviewed by Chou TW et al. [1].
The effect of particle size on the elastic-plastic deformation of metal matrix composites is studied by Nan et al.[3,4].
The elastic-plastic behaviour of symmetric metal-matrix composite laminates with in-plane mechanical loading is investigated by Bahei et al. [5].
[5] Bahei-El-Din YA, Dvorak GJ., Plasticity analysis of laminated composite plates, Transactions of the ASME (1982); 49:740–6

Wenzhe Tang et al have concluded that the project cost can be decreased 1.76% and the project time can be shorten 8.99% if the cooperation of project participants is good.
Patrick X.W.Zou et al have investigated risk factors of construction project in China and their conclusion indicates many risk factors affect the project objectives at the same time[5].
Beijing: China Architecture & Building Press.(2006) [2] Wenzhe Tang, Colin F.Duffield, David M.Young.el.
China Civil Engineering Journal (In Chinese), Vol.44(2011),p.215-219 [4] Wenzhe Tang, Maoshan Qiang et al.

Mitra et al. showed that when heavy tail noise distribution is considered, the robustness of Huber and Andrews methods is superior to that of L1 method.
Li et al. held that the computational efficiency of the Tukey and Andrews functions is lower because of the peculiarities of their weight functions.
Li et al. also showed that the performance of Fair method is superior to that of L1 method, whereas the number of calculations in Danish method is relatively greater.
References [1] Biswas, S:Pattern Recognition, Vol. 34, (2001), p. 63 [2] Pennacchi, P: Journal of Sound and Vibration, Vol. 310, (2008), p. 923 [3] Information on http://www.ingentaconnect.com/content/maney/sre/pre-prints/1752270612Y.0000000028 [4] Baselga, S: Journal of Surveying Engineering, Vol. 133, (2007), p. 123 [5] El-Hawary, F. and Mbamalu, G.A.N: IEEE Journal of Oceanic Engineering, Vol. 18, (1993), p. 142

Tao et al. [6] investigated the effect of acetic acid on phosphorus removal effeciency and demostrated the small molecular organic had no influence on phosphorus removal.
Foletto et al. [5] demostrated fulvic acid might be reacted with magnesium ions.
Tao et al. [6] demostrated the macromolecular organic could slightly reduced the phosphorus recovery efficiency.
[5] E.L.

Comparative Study of Mechanical Behavior between an Adhesive Made from Date Palm Waste and FM-73 Adhesive Sofiane MAACHOU1*, Abdeldjalil BENBAKHTI1,a, Abdelmadjid MOULGADA2,b 1University Centre of Maghnia, Al-Zawiya Road 13300, Maghnia, Tlemcen, Algeria 2University of Ibn Khaldoun Tiaret, City Zaaroura 14000 Tiaret, Algeria.
Properties of the aluminum (2024 T351) and of the graphite/epoxy. 2024 T351 graphite/epoxy EL [N/mm2] 73084.4 172369 ET [N/mm2] --- 10342,1 GLT [N/mm2] --- 4826,33 νLT 0.33 0,31 νTL --- 0,13 αL[K-1] 2.32.10-5 -7.10-7 αT [K-1] --- 3,6.10-5 Fig. 2.
References [1] Moulgada et al.
Study of mechanical behavior by fatigue of a cracked plate repaired by different composite patches, Frattura ed Integrità Strutturale 15 195-202. (2021) [2] Maleki, et al.

Fig. 1 : Schematic of Al hexagonal core sandwich panel Fig. 2 : Geometric details of Al Hexagonal core sandwich panel Edging and Joining Procedure for Securing Sound Butt Joints Configuration “A”.
In this configuration, the edges of the panel are deformed and Al sheet is inserted.
In this configuration, the edges of the panel are deformed and Al C Channel is inserted.
In this configuration, an Al sheet is inserted transversely.
NASA/CR-1999-208994, Northrop Grumman Corporation, El Segundo, California, (1999)