Search results

Influence of Sintering Temperature on Performance of Red Mud Lightweight Ceramsite Long Ma, Guozhong Lia* Shandong Provincial Key Laboratory of Preparation and Measurement of Building Materials, School of Materials Science and Engineering, University of Jinan, Jinan 250022, China amse_ligz@ujn.edu.cn, *correspondence author Key words: red mud, lightweight ceramsite, sintering temperature Abstract.
It can be used for the production of new wall materials.
Test proportion of materials was shown in Table 4.
References [1] Xiangli NAN, Tingan ZHANG, Yan LIU et al: JOURNAL OF PROCESS ENGINEERING Vol. 10(1) (2010), p. 264 [2] Xiangli XIE, Linjiang WANG, Jianxin ZHAO et al: JOURNAL OF GUILIN UNIVERSITY OF TECHNOLOGY Vol. 28(2) (2008), p. 196 [3] Peiwen LU: Elements of Inorganic Material Science (Wuhan University of Technology Publications, China 1996)
[4] Xuanye ZHAN: Sintered Brick Manufacturing and Product Property (Chinese Building Materials Industry Publications, China 2010).

When using Premiere for Chroma Keying, you need to add keying material and background material respectively in two tracks.
The background material should be below the keying material, because in most cases Keying is to control the material’s transparency to achieve the desired effect, so as to display the background layer at the bottom [5].
Research on the effect of DV video material keying [J].
Journal of Shijiazhuang vocational Technology College, 2010(04)
Journal of Weifang University, 2004 (4)

It was assumed that both the CNT and the epoxy matrix behave as linear elastic and isotropic materials.
Y. (2008) ‘Fracture toughness and fatigue life of MWCNT/epoxy composites’, Materials Science and Engineering: A, 494, 380-384
[10] Ganguli, S., Bhuyan, M., Allie, L. and Aglan, H. (2005) ‘Effect of multi-walled carbon nanotube reinforcement on the fracture behavior of a tetrafunctional epoxy’, Journal of Materials Science, 40, 3593-3595
W. (1996) ‘An introduction to composite materials’, 2nd ed., Cambridge: Cambridge University Press, 31
J. and Bernholc, J. (1997) ‘High strain rate fracture and C-chain unraveling in carbon nanotubes’, Computational Materials Science, 8, 341-348

Materials MEH-PPV was purchased from Sigma Aldrich.
The materials were used as the active layers without any further purification.
However, the two materials are mixed together and are effectively connected in series.
Binth, Journal of Surfaces and Interfaces of Materials Vol. 1 (2012) 1–7
Ben Ouada, Materials Science and Engineering: C  25 (1) (2005) 67-75.

AIAA Journal, 1984(22):561-564
AIAA Journal, 1980,18( 7):859-861
AIAA Journal, 1979(17): 1147-1148
AIAA Journal, 1985, 23(9)
Science 1983, 220:671-80 [20] J.

Journal of Purchasing.Vol.2, No.1, pp.5-17(1966)
Journal of Fujian Institute of Socialism.
China journal of management science, Vol.10, pp137-139, (2002)
Journal of Chongqing University(Natural Science Edition) Vol .29,No.1, pp.5-6,(2006)
World academy of science engineering and technology. vol.54, pp343-347, (2009).

When the support parameters and packing materials is given, the packing width will be not only one of the most important factors for gob-side entry retaining to be successful but also a significant factor in controlling the cost of support.
Journal of China Coal Society, 2012,6(37): 903-911(in Chinese)
Coal Science and Technology,2012, 3(40): 17-19(in Chinese)
Journal of China Coal Society, 2011,5(36):28-35(in Chinese)
Journal of University of Science and Technology Beijing, 2006,4(28):317-323(in Chinese)

Bhosale, Photoelectrochemical (PEC) studieson CdSe thin films electro- deposited fromn on-aqueous bath on different substrates, Bull Material Science, 30 (2007) 321-327 [2] F.
Yang, Directional CdS nanowires fabricated by chemical bath deposition, Journal of Crystal Growth, 246 (2002) 108-112 [4] H.
Kim, Diameter- tunable CdSe nanotubes from facilesolution-based selenization of Cd(OH)2 nanowire bund les for photoelectrochemical cells, Chemical Materials, 21 (2009) 1875-1883 [5] R.
Yan, Rapid formation of CdS, ZnS thin films by microwave-assisted chemical bath deposition, Materials Letters, 59 (2005) 1497-1501 [6] R.
Ito, Solar cells with Cu(In1_xGax)S2 thin films prepared by sulfurization, Solar Energy Materials and Solar Cells, 67 (2001) 225-230 [10] K.

Journal of Iron and Steel Research [J], 2006,13(4): 68-74
Journal of Nuclear Materials, 2008, 377: 72-79
Rare Metal Materials and Engineering, 2008, 37(4):610-612
Rare Metal Materials and Engineering, 2012, 41(7):1211-1215
Journal of Ballistics, 2000, 12(1):65-67

In the SeismoStruct, con_ma and stl_mp were used as the material models.
In the OpenSEES, Concrete 02 and Steel 01 were used as the material models: the former construct a uniaxial concrete material object with tensile strength and linear tension softening whereas the latter is a uniaxial bilinear steel material object with kinematic hardening.
These and material parameters were utilized in the analytical works performed on the five-story frames.
Acknowledgement This paper was financially supported by Beijing Natural Science Foundation (8142015).The authors’ deeply express sincere appreciation to them.
K. etc: Journal of Structural Engineering Vol. 137(3) (2011) p.278 [2] Honda R., Ahmed T.: Journal of Structural Engineering Vol. 137(3) (2011) p.391 [3] Masi A., Vona M., Mucciarelli M.: Journal of Structural Engineering Vol. 137(3) (2011) p.367 [4] Hancock J., Bommer J.J.: EarthquakeEngineering&Structural DynamicsVol.37(14)(2008) p.1585 [5] Dong An, Tiejun Qu: Earthquake Engineering and Engineering Dynamics Vol. 34(1) (2014) p.123 [6] Abrahamson N.A: Seismological Research Letters, Vol.6 (1) (1992) p.30 [7] Information on http://www.seismosoft.com (2013) [8] Hancock J., Watson-Lamprey, etc: Journal of Earthquake Engineering, Vol.10 (2006) p.67 [9] Lilhanand K., Tseng W.S: Proc. of the 9th WCEE, Tokyo Japan Vol.