Search results

Epoxy Resin) to bind materials at room temperature, which is available for most bonding structure between ceramic and metal.
What's more, the selection of the interlayer materials generates important effect on ballistic performance.
Experimental Procedure Materials and Specimens.
Han: Journal of University of Science and Technology Beijing, Vol. 29 (2007) No.4, pp. 402-407.
Kevin: Ceramic Armor Materials by Design, Vol. 134 (2002) , pp.635-642

Besides, the micro-hardness of coatings increases with increasing content of Cr2C3 in coating materials.
The coating materials in the layers are mainly NiAl and Cr3C2-25NiCr.
Herman: Materials Science and Engineering, A238(1997): 275
Lavernia: Metallurgical and Materials Transactions A, 31A (2000): 555-564
Ding: Journal of Thermal Spray Technology, 7(1998):242

Surface of the char is dense and compact, which can isolate the transfer of mass and heat between the materials and the flame to protect the unburned materials.
Experimental Materials POCl3 was supplied by Tianjin YongDa chemical reagent develop center.
The high IPDT implies the epoxy resins’ potential application in highly anti-thermal coatings and thermal insulating materials.
Surface of the char is dense and compact, which can isolate the transfer of mass and heat between the materials and the flame to protect the unburned materials.
Gao, Journal of Applied Polymer Science, 119 (2011) 2025 [11] V.

Due to the characteristics of geotechnical materials, more complex mined-out area compared to the structure, pillar failure affected by many factors, the collapse is a very complex dynamic process, fuzzy to a certain extent, whether the selection of a calculation method or the parameters.
Journal of Structural Engineering-Asce, 2008. 134(9): p. 1548-1557
Journal of Safety Science and Technology, 2007. 3(6): p. 68-72
Journal of University of Science and Technology Beijing, 2011. 33(2): p. 142-148. [6] Zipf, R [8] Wang Jin-an, Li Da-zhong, and Ma Hai-tao, Study of rheological mechanical model of pillar-roof system in mined-out area.
Chinese Journal of Rock Mechanics and Engineering, 2010(03): p. 577-582

Material of the clutch is GCr15.
Project supported by National Natural Science Foundation of China (Grant No. : 61074104 ) References [1] Goto S, Monahan R, Bailey T, et al.
Engines 2(1):307-313,(2009) [4] Liu Yanwei ,Zhao Kegang and Huang Xiangdong, Shift Characteristics of Mechanical Transmission Without Torque Interrupt Journal of South China University of Technology.(2011) [5] Wang Peng, Li Pingkang, Li Wenguang, et al.
Science China Technological Sciences, Vol,43(7):777~784 (2013) [6] Huang Xinhua,Liuying, and Quan Yinghua, Analysis of Self-locking of Overrunning Clutch, Journal of Mechanical Transmission.( 2007) [7] Yan Hongzhi,Yangbin and Hu Kuixian,Working Performance Analysis of Positive-continuous- engagement Type Clutch in Different Friction Conditions, Journal of Mechanical Engineering

Fig.7 shows that neglecting the damping, the conclusions of other kinds of materials used building commonly are same to steels,the dynamic stability critical length decreases as excitation frequency increases.
l For other kinds of materials used building commonly, the conclusions are same to steels,the dynamic stability critical length decrease as excitation frequency increases.
Acknowledgements This work was financially supported by the Major project of the Education Department of Anhui Province Natural Science Foundation(ZD2007007-1),The national science and technology support plan (2012BAJ08B02).
Su, Stability of Elastic system [M] Beijing, Science Press,1994,in Chinese
[9] X.D.Yang,Y.X.Tang,L.Q.Chen and C.W.Lim,in:European Journal of Mechanics - A/Solids, Volume 29, Issue 1, January-February 2010, p.81-90

Experimental Section Materials. sodium sulfide nonahydrate(Na2S·9H2O), p-dichlorobenzene(P-DCB) and N-methylpyrrolidone(NMP) were obtained from Shanghai jingchun Industrial Co.
It is because MMT had a great impact to the thermal degradation of composite materials and it can enhance the initial temperature of the reaction of volatile materials.
In addition, the layeredtablets structure from MMT play a shield, slow and insulation effect of the outflow of volatiles materials.
Journal of Applied Polymer Science, 2003, 90: 615-625
Journal Of Applied Polymer Science, 20 (1976) 2541-2551.

Introduction Zinc Oxide (ZnO) is a versatile material with unique properties, has wide applications in various photonics associated technologies.
High optical transmittance and high bandgap energy indicates the suitability of these films to use as a window materials for solar cell application.
Gong, F.F Huang, L.S Wen, ZAO; an attractive potential substitute for ITO in flat display panels, Materials Science Engineering journal B, 85 (2001), 212-217
Science, 25(3) (2007), 700-718
Natarajan, Characterization of CdTe thin film –dependence of structural and optical properties on temperature and thickness, Journal of Solar Energy Materials & Solar Cells 82 (2004), 187-199

Demir: Materials & Design, Vol. 28 (2007) No.1, p.2
Stanya: Welding Journal, Vol. 59 (1980) No.6, p.170
Zhou: Metallurgical and Materials Transactions A, Vol. 40 (2009) No.4, p.910
Messler Jr: Science and Technology of Welding & Joining, Vol. 3 (1998) No.1, p.42
Jou: Journal of Materials Processing Technology, Vol. 132(2003) No.1-3, p.102.

B. 014. 1084 Budapest, Hungary) 2 Hungarian Academy of Sciences, Centre for Energy Research, Institute of Technical Physics and Materials Science (Address: Konkoly Thege M. út 29-33., 1121 Budapest, Hungary) a nadas.jozsef@kvk.uni-obuda.hu, b rakovics.vilmos@energia.mta.hu * corresponding author Keywords: NIR LED, GaInAsP/InP LED, luminescence LED Abstract.
Experimental Selection of materials.
Ethanol is a good model material which represents organic materials well in measurements for water-ethanol (or other organic materials) systems.
[8] Rakovics V, Püspöki S, Balázs J, Réti I, Frigeri C.: Spectral characteristics of InP/InGaAsP Infrared Emitting Diodes grown by LPE Materials Science and Engineering B - Solid State Materials for Advanced Technology 91-92 (2002), pp. 491-494
[9] Rakovics V, Balázs J, Püspöki S, Frigeri C.: Influence of LPE growth conditions on the electroluminescence properties of InP/InGaAs(P) infrared emitting diodes Materials Science and Engineering B - Solid State Materials for Advanced Technology 80: (1-3) (2001), pp. 18-22.