Search results

Their shell should be resistant to high temperatures (> 300 °C) and their average diameter should be in order of 1-20 μm.
Figure 1.
Aerospace Engineering, 479-495 (2007) [3] A.A.Purichaud, R.M.Iskakov, A.Kurbatov, T.Z.Akhmetov, O.Y.Prikhodko, I.V.Razumovskaya, S.L.Bazhenov, P.Y.Apel, V.Yu.
V. 6. № 1.
V. 6. № 1.

Several oxide semiconductor- based junctions show such behavior of current [1-11].
Fig. 1 shows the sample plot of current-voltage characteristic of the constructed junctions.
Figure 1.
However, the ideality factor computed was found to be greater than 1 (@ 3.3).
References [1] R.K.

With the continuous development and application of DSP technology, it will gradually become the mainstream of the control field[1,2].
Because the PC serial port is RS232 level, the 485 to 232 transceivers are needed when connected to the PC, as shown in Fig. 1.
Fig. 1 The RS-485 communication interface of computer with TMS320F28335 Host computer design The programming software can be used VC + +[4].
References [1] Zeng Qingshuang, Jiang Wei, Yin Guoxing.Design and realization of small integrated navigation system based on high-performance DSP[J].
Harbin University of Commerce (Natural Sciences) . 2010.26（4）：475-479 [2] Li Haibing, Sheng Changxin, Fengjun.

The major elements of a longwall system are: a shearing machine, an armored face conveyor, mechanized roof supports, a stage loader, a crusher and a mobile belt tailpiece (Fig. 1).
Fig. 1.
Example of a longwall system [1] Fig. 2.
References [1] Information on http://www.5dt.com/products/ilongwall06.html
Phen., 220-221 (2015) 479-484

For a crystal Cu3Pt with shear APBs at 200 K no structural changes are made (Fig.1).
Fig. 1.
Picture of the changes of the domain structure of the alloy with shear Cu3Pt APB 1/2<110>{100} in the process of disordering.
[1] State Diagrams in Binary Metallic Systems: Reference Book in 3 Volumes, V. 1 (Ed.
J., 53, No. 5, 465–479 (2010)

Research on Morphology and Phase Structure of Al/Cu Interfaces Formed by Explosive Cladding Yan Li1, Shi-zhong Wei1,2 and Rui Long2 1 Sch.
SEM image of Al/Cu explosive cladding interface is shown in Fig. 1, it is obvious that the interface is wavelike, each wave contains front-nest, of which the average wave length is 1.0mm, the average wave crest height is 0.3mm, in a ratio of height and length is 1/3.
Al Cu a Fig. 1 SEM images of Al/Cu interface.
References [1] Z.
Forum Vol. 479 (2005), pp. 3855.

Experimental Methods Table 1 demonstrates the chemical analysis of AISI S1 used in this study.
In the case of 48 h of soaking time, the required tempering time was 1 h.
References [1] J.
[4] B.S., 10002–1, Metallic materials tensile testing, Part 1: method of test at ambient temperature, British Standards Institution, UK, 2001
Junik, Effect of cryogenic treatment on distribution of residual stress in case carburized En 353 steel, Materials Science and Engineering: A, 479 (2008) 229-235

Also, the influence of changing the slope for the temperature gradient concerning the position of the primary crack under the contact surface in thermomechanical contact fatigue is of major importance [1].
Fig. 2 Temperature gradient according Jacq anomaly [6] Fig. 1 Classic gradient for temperature in a metal wall [6] Hence, below the surface, between very near levels, different thermal stresses are generated.
The thermal Jacq effect gives a strong support for the localization of the primary crack under the contact surface, for the thermomechanical contact fatigue [1].
References [1] F.
Balkan Journal of Tribology, 2005, BalkanTrib ’05 – 5th International Conference on Tribology, June 15-18, 2005, Kragujevac, Serbia and Montenegro, pp. 474-479

Whyte 1,a, D.J.
Hadden 1,b , I.R.
Gibson 1,2,c and J.M.S.
Figure 1.
Krist. 219: 479-486

The wall-thicknesses of 2.1 for pultrusion and 1.6 mm aluminum wrap 1 layered were examined at the material fiber type of E-glass reinforced polyester resin of square cross-section subjected to axial quasi-static loading.
Crushing during internal energy is one of the significant factors in their application in applied vehicle crush structures [1].
The tube profile for thin-walled aluminum tubes E-glass wrapped polyester reinforced composite was quite different from the data either quasi-static absorbed energy and initial peak load as well as mean load shown in Fig. 1 and Fig. 2.
Fig. 1.
Vol. 337 pp: 479-488