Search results

Test Materials Preparation and Microstructure Analysis of Cutting Inserts.
Tool life is the most basic and most important criterion to judge the performance of a cutting insert materials, it is mainly obtained through the tool wear test data.
References [1] Chenguang Lin: Chinese Journal of Rare Metals, Vol.28 (2004), p.762, In Chinese
[2] Chongbin Wei, Xiaoyan Song, Jun Fu, et al: Materials Science and Engineering of Powder Metallurgy, Vol.17(2012), p.315, In Chinese
[3] Shouquan Zhang: Materials Science and Engineering of Powder Metallurgy, Vol.14 (2009), p.237, In Chinese

China 2State Key Laboratory of Optoelectonic Materials and Technologies, School of Physics and Engineering, Sun Yat-sen (Zhongshan) University, Guangzhou, 510275, China aemail: mmwangxf@163.com, bemail: dafang_09@126.com, cemail:tianle_li@163.com, demail:wangfj@mail.sysu.edu.cn Key words: ZnO nanoparticles, size-dependence, surface states Abstract.
The luminescence properties of such nanostructures are substantially different from those of bulk crystalline materials [5-7].
Acknowledgments This work was financially supported by the Science and Technology Program of Guangdong Province (2010B080701066), Foundation for Distinguished Young Talents in Higher Education of Guangdong (2012LYM0097), Research Fund for the Doctoral Program of Guangdong University of Petrochemical (511022), and Foundation for Science and Technology Program of Maoming, China (201338).
Datta, Indian Journal of Physics, Vol. 87 (2013), p. 1177
Datta, Indian Journal of Physics, Vol. 87 (2013), p. 1177

Material parameter of specimens is the same as test of Packer J.A, steel yield strength of chord and bracing is 400 MPa, ultimate strength is 443 MPa, cylinder compressive strength of concrete is 30 MPa.
Material mechanical The stress vesus strain of steel is based on double-line elastic-plastic model.
Acknowledgements This work was financially supported by the National Natural Science Foundation of China (51178051, 5178068), Construction Technology Program of Ministry of Transport (2013318812410) and Technology Project of Shaanxi Provincial Transport Department (13-26K).
Cold Formed Tubular Members and Connections: Structural Behaviour and Design(Elsevier Science Ltd, 2005) [4] Packer J A.Concrete-Filled HSS Connections submitted to Journal of Structural Engineering(1995)
Experimental Research on Rectangular Steel Tube X-joints with Chord Concrete-inside Subjected to Tension and Bending submitted to Journal of Building Structures(2009)(in Chinese)

Besi, 57000, Kuala Lumpur, Malaysia 2School of Applied Physics Faculty of Science and Technology, UniversitiKebangsaan Malaysia, 43600 UKM Bangi, Selangor Malaysia aaienib1607@ymail.com, ,bafauziah@upnm.edu.my Keywords: natural cellulose, pineapple leaf fibre (PALF), XRD.
Experimental Materials.PALF was obtained from the local plantation in Pekan Nanas, Pontian, Johor, Malaysia.
Nayak: Indian Journal of Traditional Knowledge 9(2), (2010), p. 386-393
Satyanarayana: Journal of Materials Science 21 (1986), p. 51-56

An improvement method for extracting five parameters of a solar cell based on Lambert W-function with the current-voltage data Zhongzheng Zhang a, Xiaofang Cheng b, Jinlong Liu c Department of Thermal Science and Energy Engineering, University of Science and Technology of China, Hefei, Anhui 230027, China azzzustc@mail.ustc.edu.cn, bxfcheng@ustc.edu.cn, cljinlong@mail.ustc.edu.cn Keywords: Solar cell, Five-parameters, Current-voltage characteristics, Extraction Abstract.
Solar Energy Materials and Solar Cells. 90(3): 352-361
Solar Energy Materials and Solar Cells. 94(8): 1358-1370
Journal of Applied Physics. 110(6)
International Journal of Solar Energy.

To guarantee that the material removal state on both sides was symmetrical, spiral down milling method was selected in the both process plans in the experiment.
Under the premise of the same material removal volume, average deformation generated in uniform allowance process δmean is equal to 0.21mm, and that in non-uniform allowance process is 0.102mm.
Acknowledgements The authors wish to thank the support of the National Science and Technology Support Program for Efficient High-speed Cutting Tools of Research and Development, China (Grant No. 2008BAF32B10).
Bravo, OAltuzarra, LNL pezdeLacalle: International Journal of Machine Tools & Manufature,45(2005):1669~1680 [3]E.
Budak: International Journal of Machine Tools and Manufacture, Vol.46,N0.12-13(2006):1489~1499

With decreasing pouring temperature, the density of primary solid particles increased greatly, the size of primary solid particle evolved to coarse. 1 Introduction Microstructures are at the center of materials science and engineering.
They are the strategic link between materials processing and materials behavior[1,2].
Journal of Materials Processing Technology, 2009, 209: 2092–2098
Journal of crystal growth, 1977, 37: 309-316
Uggowitzer, Fundamentals of new rheocasting process for magnesium alloys, Advanced Engineering Materials, 2001, 3, No.12 963~967 [12] F.

Furthermore, moisture absorption of the materials can also be decreased, which is beneficial for preparing low-κ materials.
Recently, many efforts have been made to prepare novel fluorinated epoxy materials by incorporating trifluoromethyl group [5-11].
Experimental Materials.
Nalwa: Low and High Dielectric Materials (Academic Press, San Diego, 1999) [5] J.R.
Journal of Applied Polymer Science, Vol. 124(2012), p. 2615 [11] M.

Introduction Joining materials using adhesive joints offer several benefits, but also limit factors if compared with using mechanical joints.
Experimental Materials For this experiment three types of thermoplastic materials were used: - Low Density Polyethylene LDPE DOW – LDPE 780E, DOW – Chemical Company, - Polycarbonate PC – MAKROLON 2405, BAYER Company.
Brockmann et al., Adhesive Bonding: Materials, Applications and Technology, WILEY-VCH, Weinheim, 2009
Ebnesajjad, Surface Treatment of Materials for Adhesion Bonding, William Andrew Publishing, Norwich, 2006
Vijayalakshmi et al., Studies on modification of surface properties in polycarbonate (PC) film by DC glow discharge plasma, International Journal of Polymer Science 2011 (2011) 1-7.

The wear volume of tube materials was less than those of supports under all conditions.
As shown in Fig. 2 (a), wear volumes for the two tube materials were not significantly different.
The wear volume of tube materials was less than those of supports under all conditions.
Kim, Materials science forum, Vol. 486-487 (2005) 137-140 [7] E.
Rabinowicz, Friction and Wear of Materials, Wiley, New York, 2nd ed. (1995) 44-48 [8] P.