Search results

However, there is an opposite effect, and, according to the experimental data, it could be more important.
In particular, from the data given in Fig. 4, it follows that c−37(NO3) = 0.53 M.
The data in the ZrNb alloy show the behavior of S(t) in the absence of Ps atom formation.
Similar data were obtained in [32], black circles, however, they were not included in the fit (red curve).
We used these formulas to fit the data on the variation of the R-parameter vs. magnetic field, Fig. 13.

The welding arc is an extremely dynamic and variable process, continuously affected by a number of physical and metallurgical disturbances [3] such as: - ionization process of gases and metal vapour; - deposition and transfer of melted weld metal and slag; - metallurgical reactions of reductions and refinement of weld metal in puddle.
Slania, Objective methods for assessing the performance of welding power sources via a computer recording device and data processing, a general discussion, Welding Institute Bulletin (1991), N. 2-3 (in Polish)

However, the decrease of flying height will cause the occurrence of intermittent contacts, which lead to slider wear, the loss of data and even catastrophic failure of hard disk drive.
More precise simulation of slider-disk interaction dynamics is required for the reduction in the slider-disk spacing.

Then, in the high temperature tube furnace, the synthesis was performed at 1300 oC for three hours with a weak reductive atmosphere of flowing 5%H2-95%N2 which ensured complete reduction of Eu3+ to Eu2+.
The 1800s data were recorded.

Therefore, Chen and Lee [11] developed an intelligent fuzzy weighted estimator with higher target tracking performance and better noise reduction effectiveness.
The input estimation method uses the recursive form to process data.

The data demonstrate that the residual carbon source (ethanol) could be used for denitrifying reaction of next cycle, but the relative denitrifying rate will was decreased with the ethanol solution reused times.
Thus, the reductions of nitrate and nitrite were limited due to insufficient carbon source at these days.

Zhao[4] experiments that adopted axial vibration, the normal grinding force can be reduced by 1/3 to 1/4, and the across axis direction leads to a significant reduction of grinding forces and an increase in material removal rate while maintaining a slightly increase in wheel wear and surface roughness.
Measure equipments includes: ONO SOKKI LV-1710 Laser Doppler Vibrometer systems to measure the tiny amplitude; KISTLER Type-9257B dynamometer; Mitutoyo SJ-301 Surface Roughness Measurement; Sartorius RC 210 D Data Weighing Systems measures the amount of removal material; JEOL JSM-5610LV SEM to observe surface formation.

Therefore, this paper analyses thermodynamic data, the mechanism of the La and Ce elements in the process of Cu-Cr-Zr alloy non-vacuum melting, and discuss the Impact of La and Ce on the alloy's microstructure and properties using as additive Elements.
There are three factors mainly: 1) the addition of La and Ce can eliminate pine-tree crystal, fine grain remarkably, as well as react with the low melting point metal to form insusible compound which disperses in the matrix to improve the tensile strength and micro-hardness of alloy; 2) the atom size of La and Ce is much more bigger than the atom size of Cu, as a result of which produce many vacancy during crystallization, these vacancy are benefit to the solution of Cr, Zr and reduction of big primary phase Cr, Zr and improves the tensile strength and elongation of alloy; 3) the effect of degassing, dedusting and edulcoration of La and Ce makes the elements such as P, Si, Pb and so on which are harmful to the electrical conductivity discharge with the dregs, therefore, the alloy matrix and grain boundaries are cleared and the electrical conductivity and elongation are increased.

As can be seen from the data, the electrical conductivity of samples increased gradually with the increasing temperature from 303 K to 773 K and reached the extreme 2.78 S/cm and 3.25S/cm respectively at 773K.
The economics of inert anodes and wettable cathodes for aluminum reduction cells [J].

Despite efforts to conserve these ecosystems, the data obtained from monitoring programs has shown that a decline in coral cover continues to appear, which makes it clear that the implementation of new technologies is required to mitigate these problems.
The ceramic break went through a size reduction process using a roller mill.