Search results

Grumbine[11] discussed the ten dominant themes of ecosystem management: hierarchical context, ecological boundaries, ecological integrity, data collection, monitoring, adaptive management, interagency cooperation, organizational change, humans embedded in nature, values.
References [1] Yuan Yu: Tropical Geography Vol. 31(1) (2012), p. 22-31 (In Chinese) [2] Jean-Francois Donzier: Express Water Resources & Hydropower Information Vol. 30(9) (2009), p. 44- 46 (In Chinese) [3] Yu Yang: From Decentralized Autonomy to Central Governance: Case of Murray-Darling River Basin and Its Implication for the Governance of Tai Lake Basin, in 2009 International Conference on Management Science & Engineering (16th), Moscow, Russia, (2009), p. 2143-2149 [4] Xiao-feng Liu, Zhao-han Sheng and Shuai Jin: China Population, Resources and Evironment Vol. 21(2) (2011) p.73-78 (In Chinese) [5] Demi Zhu: Chinese Public Administration Vol. 286(4) (2009), p. 86-91 (In Chinese) [6] Chi Zhang: Knowledge Economy Vol. 10 (2007), p.78-80 (In Chinese) [7] Zhen-peng Hu: Meteorology and disaster reduction research Vol. 129(6) (2006), p. 1-7 (In Chinese) [8] Jing-wei Luo, Bo-fu Zheng, Wan-you Qian and Cheng-lin Liu: Journal of Nanchang University (Engineering & Technology

This is due to pressure reduction of oil reservoir.
These two types are not the most common drivers for oil field compressors. [2] In the concerned project the main results and analysis of data acquired during the reservoir study confirmed that: 1- The Injection gas is in miscible condition with reservoir oil. 2- The gas re- injection guarantees a higher ultimate recovery factor 3- The injection gas pressure should be about 500 barg.

Further animal trials reported by Zberg et al [15] clearly revealed that glassy Mg60+xZn35-xCa5 (0 ≤ x ≤ 7) alloys showed a great reduction in hydrogen generation and possess the same good tissue compatibility as crystalline Mg implants.
Magnesium Technology: Metallurgy, Design data, Applications.

[5] Van Tung Phan, Jochen Katja, Bohlke Thomas, Simulation of Sheet Metal Forming Incorporating EBSD Data, Journal of Material Processing Technology, vol.212, pp 2659-2668 (2012)
[13] Xu Dongkai, Chen Jun, Tang Yucheng, Cao Jian, Topology Optimization of Die Weight Reduction for High-Strength Sheet Metal Stamping, International Journal of Mechanical Sciences, vol. 59, pp 73-82 (2012)

The reduction of the A2 lattice parameter in the fc sample in contrast with the wq sample is a clear evidence of the formation of the D03 ordered phase [9].
High resolution XRD data confirms the ordering of Ga atoms into a metastable D03 structure during furnace cooling.

Based on these data, the samples were sintered at a temperature of 1410 ° C, with a holding time of 2 hours and a heating rate of 3 ° C / min.
Despite the fact that the mechanical properties of the obtained ceramics, at the moment, are not significantly inferior to the properties of the samples obtained by traditional ceramic technologies, the proposed technology benefits from a reduction in cost, production time and energy costs, as well as due to the possibility of manufacturing ceramics with complex topology.

The traditional use of dragon fruit tree had been discovered to promote healing wounds and cut, improves appetite, eye sight, weight reduction and improves memory [3].
The data recorded for three replicates of each concentration of BAP and Kinetin were plotted in graph form and comparison was made.

The heating rates were selected based on the data from the literature and preliminary studies and were Vheat=15°C/c; Vcool=7,5°C/c respectively.
The final, grain radius after thermal cycling, similarly to the discounting operation, can be calculated by the formula (1) (1) where – relative reduction in grain radius as a result of a single processing cycle; n – number of thermal exposure cycles.

By computer network the enterprise constructs intelligent dynamic system on shopping -- warehouse - production material and carries out material data keeping update so as to buyers determine reasonable purchase batch and purchase time for avoiding the backlog or shortage of inventory loss.
The enterprise should use the production equipments of energy conservation and emission reduction, and enforce lean manufacturing to avoid the largest extent wastes.

Therefore, type k thermocouples were used with the radio data logger (measuring amplifier) Cobra SMARTsense, PHYWE Systems, Germany.
The friction-spinning process with driven tool leads to a maximum temperature of Tmax = 510 °C with a wall thickness reduction from s0 = 5 mm initial thickness to s = 2.7 mm flange thickness.