Search results

Yang, et al.: Materials Science & Engineering A, Vol. 260 (1999), p. 269
Mabuchi: Journal of Materials Science: Materials in Medicine, Vol. 13 (2002), p. 397
Silva: Materials Science and Engineering Vol.
Cairo: Materials Science Forum Vol. 498-499 (2005), p. 40
Silva: Journal of Materials Processing Technology, Vol. 5267 (2001), p.1

It concludes that the breast root girth is a complicated three-dimensional curve; it’s inappropriate for the neighboring size’s brassieres to adopt the steel ring with the same specification; the material design of the steel ring should be moderate.
Journal of Textile Research, 2007, 28(8):75-78.
Journal of Textile Research, 2008, 29(12):73-77.
Journal of Xi’an University of Engineering Science and Technology, 2006, 20(5):555-559.
Shanghai: Shanghai science and technology publishing house, 2004, 6:31-55.

Among the non-traditional machining methods currently proposed for the hard-brittle materials, rotary ultrasonic machining (RUM) is regarded as a relatively cost-effective process that combines the material removal mechanisms of ultrasonic machining (USM) and conventional grinding (CG) [1].
Since the birth of RUM in 1960s, it was primarily applied to drill core hole on brittle materials [3].
Tang: International Journal of Machine Tools & Manufacture Vol. 52 (2012), p. 77 [2] D.X.
Haselkorn: International Journal of Machine Tools and Manufacture Vol. 35 (1995), p. 1033 [5] D.X.
Wang: Journal of Advanced Manufacturing Technology, DOI 10.1007/s00170-012-4509-1 [6] Z.

The artificial CSOs shall be flowing into the filter performance evaluation device by flow regulator and then discharged after the polluted materials are settled or filtered.
SEM images of solid fabric filter media As shown in Table 1, materials of solid fabric filter media consist of polypropylene and polyethylene.
Oh, in: Development on Materials for Reducing Pollutant Discharge on the Impervious Cover (4th year), edited by Korea Institute of Construction Technology, Korea (2008)
Svensson: Water Science Technology Vol. 46 (2007), p.191-198
Evett: Journal of Environmental Engineering Vol. 124 (1998), p.987-993

Previous research conducted on 3D braiding structural composites has shown that they can be considered as alternative materials since they are less prone to delamination and more damage tolerant as compared to laminates.
Materials properties of fiber and resin Fiber Ef1/GPa Ef2/GPa Gf12/GPa Gf23/GPa μf12 Resin Em/GPa μm T700-12K 230 40 24 14.3 0.26 Epoxy TDE 86 3.5 0.35 Table 2 shows the properties predicted by the analytical models and the experimental results.
Chinese Journal of Aeronautics, 2003, 16(3):142-150
Journal of Composite Materials, 2004, 64(19-20):395-448
Journal of Aeronautical Materials, 2015, 35(3):89-96.

Experimental Materials.
All materials were used as received without further purification.
The amounts of all materials used are given in Table 2.
Acknowledgements The authors gratefully acknowledge the Department of Materials Science, Faculty of science, Chulalongkorn University for instrument support.
Vaysse, and S.Liangprayoon: Kasetsart Journal (Natural Science).

Introduction Fiber reinforced concrete is a new composite materials of contemporary rapid development, especially the development of steel fiber reinforced concrete and synthetic fiber concrete is the fastest.
Experimental Program Materials and Concrete Mixture Proportioning.
The materials used in this research were 42.5R ordinary portland cement type, coarse aggregate with gravel.
The axial tensile strength tests used Instron 1342 servo-controlled hydraulic materials testmachine as a loading device, been in control of equal displacement mode; the loading rate is 0.01mm/min.
[3] Dongtao Xia, Lihua Xu and Yin Chi: Journal of Shenyang Jianzhu University (Natural Science Edition) Vol. 1 (2007), p. 77

Proper ratios of sol matrix materials and gelation agents were determined.
Materials and Methods Two different commercial SiO2 sols were evaluated in the study.
Mao, The Characteristics of Silica-Sol Combining Refractories, Advanced Materials Research, 396–398 (2011) 288–291
Tokarz, Silica sols as refractory fibre binders, Journal of The European Ceramic Society, 21 (2001) 795-808
Souri, Microstructure and properties of colloidal silica bonded magnesite castable refractories, Iranian Journal of Material Science and Engineering, 8 (1) (2011) 25-31

Journal of Materials in Civil Engineering, 28(1), 04015062. https://doi.org/10.1061/(asce)mt.1943-5533.0001291 [4] ASTM, (2020).
Materials Science Forum, 840, 389-393. https://doi.org/10.4028/www.scientific.net/msf.840.389 [24] Rashid, M.
Journal of Material Cycles and Waste Management, 20(2), 1090-1098. https://doi.org/10.1007/s10163-017-0672-7 [25] Reddy, M.
IOP Conference Series: Materials Science and Engineering, 374, 012068. https://doi.org/10.1088/1757-899x/374/1/012068 [34] Zhang, L. (2013).
Production of bricks from waste materials – A review.

Tsao 2 1 Department of Materials Science and Engineering, National Cheng Kung University, Tainan, Taiwan, China, email:sam3903@ms64.hinet.net 2 Department of Materials Science and Engineering, National Cheng Kung University, Tainan, Taiwan, China, email: tsaocya@mail.ncku.edu.tw Keywords: Al/Sip MMC, Spray Forming, Workability Abstract.
The chemical compositions of all the materials used are listed in Table 1.
Effects of materials.
Korevaar: Journal of Materials Science Vol. 27 (1992), p. 4247
Lau: Journal of Materials Processing Technology Vol. 63 (1997), p. 395