Search results

All materials parameters except for surface chloride content are expressed as a function of time.
This work is accomplished with the HYMOSTRUC[6], based on the knowledge of material science.[7]~[10] The diffusivity of cement paste is transformed into that of concrete using EMT theory.[11] Fig. 5 shows the calculation results.
Summary The purpose of this study is to set up a framework for defining materials parameters which can be used for durability design of marine concrete.
Bazant: Modeling Chloride Penetration in Saturated Concrete, Journal of Materials in Civil Engineering Vol.11, No.1, ASCE (1999) [13] V.
Fardis: Physical and Chemical Characteristics Affecting the Durability of Concrete, ACI Materials Journal Vol.8, No.2 (1991) p.186-196

Therefore, the overlapped cushioning materials are introduced.
Guo et al [14] analyzed the cushioning coefficient of overlay cushions composed of the same materials.
However, the cushioning properties of overlapped cushions composed of dissimilar materials are not focused on enough.
M. wang: Journal of Sandwich Structures and Materials, Vol. 11 (2009) No.1, pp. 57-66
Rusch: Journal of Applied Polymer Science, Vol. 13 (1969) No.11, pp. 2297-2311

The Design of Melting Units for Production of Synthetic Fibrous Materials by Vertical Blowing Method from PET Raw Materials Vladislav Sviatskii1,a, Andrea Mudriková2,b*, Radovan Holubek2,c*, Jakub Horník3,d and Mikhail Sokolov4,e 1Department “Technology of mechanical engineering and instrument making" Votkinsk Branch of Kalashnikov Izhevsk State Technical University, Russia 2Slovak University of Technology, Faculty of Materials Science and Technology, Institute of Production Technology, J.
Introduction Synthetic fibrous materials from PET-raw materials are widely used in various fields of human activity.
As a raw material for production fibrous materials you can use, for example, primary or secondary granulated PET-material and also flexes, obtained after crushing of used plastic containers and other packing materials.
Materials and Methods One of the most important tasks, when designing units for production of fibrous materials by vertical method of blowing molten material jet with the compressed air stream, is the calculation of expected process performance.
Mchedlishvili, Determination of the micropores’ size of nuclear microfilters with a small diameter // Engineering and Physics Journal. (1979) Т.37. p.119

Fu, Study on the effects and mechanisms of induction heat treatment cycles on toughness of high frequency welded pipe welds, Materials Science and Engineering: A, 736 (2018) 276-287
Inoue, Effects of carbon and chromium on microstructure evolution and mechanical properties of friction stir weldment in medium-carbon steel, Materials Science and Engineering: A, 762 (2019) 138060
Andilakhai, Tailoring strength/ductility combination in 2.5 wt% Si-alloyed middle carbon steel produced by the two-step Q-P treatment with a prolonged partitioning stage, Materials Science and Engineering: A, 791 (2020) 139721
Du, Mechanism and prediction of hydrogen embrittlement based on complex phase structure of chromium alloy steel, Materials Science and Engineering: A, 822 (2021) 141546
Li, et al., Friction and wear behavior of Ni-based alloy coatings with different amount of WC–TiC ceramic particles, Journal of Materials Science, 58 (2023) 1116-1126

Nanostructured materials.
Applied Mechanics and Materials, 695, 98–101
Materials. 2018; 11(5):704
Materials Today: Proceedings, 18, 4255-4262
Jasim, Journal of Materials Research and Technology, Volume 8, Issue 1, January–March 2019.

Both nano ferric oxide thin film materials prepared and the modified were characterized by SEM, XRD.
Nano thin film materials are the most dynamic part with the wide application [1] in the new materials field, Nano thin film materials refers to the film which is composed of nano-size grains or nano layer of whether single or multilayer.
Experimental Materials.All reagents were AR grade.
Y.Han: Chinese Journal of catalysis, Vol. 19(1998),p.7 [10] Y.
K.Liu, Y.J.Feng, X.W.Wu, Y.Wang: Materials science and technology, Vol. 2 (2010), p.262

The ordinary method is packaging with polymer material in axisymmetrical structure [7].
But the pressure sensitivity is still not high enough because of the property of the polymer material in this method.
Acknowledgment This work was financially supported by the Natural Science Foundation of China（No.60901054）.
Liao: Chinese Journal of Lasers Vol.35 (2008), p. 1940
Jiang: Journal of Transducer Technology Vol. 23 (2004), p. 12

With the development of material science, modern all-ceramic materials have obviously improved its mechanical strength.
Mclean: The science and art of dental ceramics and esthetics.
Part I: Core materials.
International Journal of Stomatology.Vol.30 [6] (2003), p.467
Chinese Journal of Prosthodontics.

The new phenol removal materials mainly include the development of potassium permanganate composite reagents and new adsorbent resins.
The new phenol removal materials also include KDF metal filter and adsorbents of high performance, such as clay materials modified by surface activator, ceramic particles modified by iron oxides and so on [9-12] .
Acknowledgment This paper is supported by National Natural Science Foundation of Heilongjiang Province (Grant No.
Journal of Harbin University of Commerce Natural Sciences Edition, Vol 20 (2004), No 2, p.199-202 [3] D.M.
Journal of Shenyang Jianzhu University (Natural Science), Vol 24 (2008), No 4, p. 633-636 [14] Najm, Issam N., Tate, Carol, Selby, Douglas.

The effect of covering materials on the solar greenhouse light environment.
Covering materials have significant effects on the indoor temperature and light.
Study of greenhouse covering materials thermal properties.
Greenhouse covering materials thermal properties.
The testig of greenhouse glazing materials transmittance properties.